Your search resulted in 9 documents.
A comparison of the effectiveness of a vacuum oven and a wind tunnel in the accelerated ageing of treated wood by evaporation
1989 - IRG/WP 2334
R J Orsler, G E Holland
Alternatives to preliminary oven-drying prior to spot-testing treated timber for borate or TBTN preservative penetration
1995 - IRG/WP 95-20067
Commonly-used penetration test procedures for timber treated with borate or organotin wood preservatives demand preliminary oven-drying before application of the spot-testing reagent(s), in order to achieve reliable results. The delay of 12 hours or more during oven drying is often a nuisance. Modifications to the spot-testing procedures, involving alternative solvents and acidification conditions...
M J Kennedy, A Zosars, J Norton
Influences of the hydro-thermal treatment on physical properties of beech wood (Fagus orientalis)
2005 - IRG/WP 05-40303
Influences of the hydro-thermal treatment on physical properties of beech wood were studied. Wood specimens (2×2×2cm) were treated in two steps. At first step, samples were treated at 160,180 & 200ºC for 4, 5 & 6 hours. At second step, treated samples were cured based on their first step treatment temperatures (160,180 & 200ºC) for 16 hours. The treated samples were soaked in water...
B Mohebby, I Sanaei
Experiments in accelerated ageing
1984 - IRG/WP 2223
Experiments using a vacuum oven to accelerate the evaporative loss of g-HCH from treated wood blocks have indicated that the method described in this paper has the potential to reproduce in a relatively short time the distributions and loadings of the insecticide that are found during natural ageing. By contrast, the wind tunnel removed the volatile material in a way not found in natural ageing an...
R J Orsler, M W S Stone
The effects of accelerated drying of green Pinus radiata on its attractiveness to Anobium punctatum as an egg-laying site
1984 - IRG/WP 1199
The methods and results are given for a series of experiments in drying Pinus radiata sapwood under a variety of conditions, then exposing the material to Anobium punctatum egg-laying. The results showed very clearly that the attractiveness of the wood to gravid females was drastically reduced when dried from green at temperatures much above 35°C. Both simple oven drying and steam kilning produce...
D J Cross
Influence of ring width and wood density on durability of oak heartwood
2008 - IRG/WP 08-10639
Oak (Quercus sp.) is considered as one of the most durable European wood species. The most important factor influencing oak durability was extractive content. In our work, we were interested in if oak-wood durability is affected by ring-width and related density. Therefore, oak heartwood specimens made of boards with different ring widths were exposed to five different fungal species Daedelea quer...
M Humar, P Oven, F Pohleven
Material Resistance and Chemical Composition of Italian Stone Pine (Pinus pinea)
2018 - RG/WP 18-20645
Relevant properties of stone pine (Pinus pinea) wood have been only fragmentarily addressed in the past, which has been recognized as a limiting factor for its potential applications. The amount of the respective wood species on the market will likely increase in the future. The sorption properties, permeability to water, extractives content and durability against fungi of Pinus pinea sapwood and ...
M Humar, M De Angelis, M Romagnoli, V Vek, I Poljanšek, P Oven, N Thaler, B Lesar, D Kržišnik
Impregnation of wood with antifungal compounds from low-quality tree biomass
2022 - IRG/WP 22-30763
In this paper we have reviewed recent research on the development of bio-based preservative formulations for wood done at the Department of wood science and technology, Ljubljana. Preservative formulations used in this investigation were prepared using plant polyphenols as biocidal agents. These nonstructural components of wood were stilbenes and flavonoids, and were extracted from wood of broken ...
V Vek, I Poljanšek, A Balzano, M Humar, P Oven
Chemical modification of cellulose nanofibrils for tailoring properties of composites
2022 - IRG/WP 22-40934
Due to its natural abundance, complete biodegradability and excellent properties, cellulose is one of the most promising materials for the production of bio composites, as well as one of the most promising fillers for biodegradable polymer composites. This is also true for nanocellulose. A large number of hydroxyl groups on the surface of fibers or fibrils enables a whole series of chemical reacti...
I Poljanšek, J Levanič, V Ž Bogataj, V Vek, P Oven