Your search resulted in 178 documents. Displaying 25 entries per page.
Effect of climate, species, preservative concentration and water repellent on leaching from CCA-treated lumber exposed above ground
2001 - IRG/WP 01-50178
Few studies have examined leaching of chromated copper arsenate (CCA) from treated wood in above ground exposures due to the assumption that leaching is less severe compared to wood in continuous contact with soil or water. However, a significant portion of CCA treated wood is used for above ground applications, exposing considerable volumes of the preservative to precipitation and potential leaching. This paper presents preliminary results of a one-year study that continuously monitors CCA leaching from above ground, naturally exposed 5.08 cm x 15.24 cm (2 x 6 inch) dimensional lumber. Three wood species, southern yellow pine (Pinus spp.), jack pine (Pinus banksiana Lamb.), and black spruce (Picea mariana (Mill.) B.S.P.), along with two preservative concentrations and one commercial water-repellent are evaluated for their effect on leaching rates. Preliminary leaching results indicate significant differences between wood species, treating solution concentrations, and the use of water repellent. In addition it appears that climatic variables affect elemental leaching of copper, chromium and arsenic differently. However, the exact effects of climatic variables are inconclusive at this time. Upon completion, this study will offer a substantial amount of leaching data to validate the findings of previous leaching tests, and provide insight into the leaching mechanism of CCA-treated lumber in above ground exposures.
J L Taylor, P A Cooper
Wood preservatives treatment of black spruce
1997 - IRG/WP 97-40092
A representative sample of black spruce logs from Central Newfoundland was harvested and processed to dressed 2"x4" lumber. Over 400 pieces of lumber were then incised and treated with ACQ preservative in a semi-industrial retort. 9 charges of 20 samples were used to determine treating parameters and 11 charges of 20 pieces were treated using the optimized process. This material was inspected by an independent inspection agency. It has been found that black spruce wood incised to about 9500 incisions per square meter and treated at about 50° C using a 4.5 hour standard full cell process can be treated to the penetration requirements of the AWPA and CSA standards for in-ground application. In regards to retention, all charges fulfilled the requirements for above ground application, but only 4 of 7 charges targeting a 0.40 pcf (6.4kg/m3) in-ground retention met this requirement. It is believed that this was the result of using a standard black spruce wood density for retention calculations, when the wood actually had a much higher density.
A R Zahora, J P Hösli
Status of the research and development of a new preservative system (EFPL) for pressure treatment of spruce in Canada
1975 - IRG/WP 348
Our work has been to develop a system which would have the stability of the ACA system and the formulation flexibility of the CCA system enabling properties such as fixation of arsenic, water repellency, appearance and cost to be controlled. Our permeability studies of spruce using a method previously developed indicated that an ammoniacal solution of copper arsenate is an excellent candidate for the treatment of spruce. Studies of the permeability of spruce sapwood microsections to CCA preservative and to an ammoniacal solution of copper arsenate proved that the ammoniacal system penetrates 1.7 to 1.8 times faster than the CCA system, in the radial direction. The permeability in the tangential direction was on the average 3.8 times better. These results were confirmed by pressure treatments of spruce lumber and spruce roundwood with both preservatives.
J Rak, M R Clarke
Comparison of cubic and plug samples for preparation and data assembly in permeability study
2000 - IRG/WP 00-20197
In order to determine if plug experimental samples (PES: 30 x 15 mm2 diameter) could be used for inspection of wood permeability characteristics, radial and longitudinal flow directions were prepared according to either PES or cubic experimental samples (CES: 100 x 20 x 20 mm3) from the sapwood zone of Sitka spruce and treated by tanalith-C according to full-cell process. Results from the two preparation techniques agreed in the test to determine the mean percentage of void volume filled by liquid both radially and longitudinally, while the preparation process (i.e. machining, sealing, etc.) of the experimental samples and the period of the data collection was quite longer in CES than that for PES in either flow direction.
Problem of the treatment of dried sawn spruce building timbers with water-borne preservatives. Interim reports for discussion at the 4th Annual Meeting in West Berlin on 27 October 1972
1972 - IRG/WP 311
One of the most difficult technical problems facing the preservation industry is how to improve the treatment of refractory species of timber such as spruce. Its resistance to penetration, even under pressure' precludes its use for more hazardous service situations, and even in less severe conditions a higher level of treatment would be desirable. The importance of this subject led us to look once again at possible ways of improving treatment.
W Liese, J W W Morgan, T Hof, R O Ullevålseter
Cu, Cr and As distribution in soils adjacent to CCA treated utility poles in Eastern Black Sea Region of Turkey
2004 - IRG/WP 04-50214
In this study, the main objective was to asses the distribution of Cu, Cr, and As in soils adjacent to CCA treated utility poles in Eastern Blacksea Region of Turkey (Trabzon, Rize and Artvin ) and determine the influence of soil composition. Surface (0-5cm), subsurface soil samples (30-40cm) were collected near CCA-treated utility poles and control soil samples away from CCA-treated utility poles were also collected. Water holding capacity, pH, mechanical properties of soil samples were determined for both depth levels. Results showed that Cu, Cr and As concentration in soil samples taken from all three cities in 0-5cm depth was higher than soil samples taken from 30-40cm depth. Cu, Cr and As concentrations were much higher in soil samples taken from city of Rize.
E D Gezer, Ü C Yildiz, A Temiz, S Yildiz, E Dizman
Spruce lumber treatments with ammoniacal solutions of inorganic preservatives
1977 - IRG/WP 391
As a part of our work in the Wood Preservation group at the Eastern Forest Products Laboratory in Ottawa to facilitate exploitation of spruce, which is a large timber resource in Canada, we have been studying the treatability of spruce roundwood. A report on this subject was presented to this group last year. More recently, another commodity - spruce timber - has been rapidly gaining the interest of wood treaters, mainly because of its potential use in permanent wooden foundations. We identified this trend and extended our research work to the treatability of spruce lumber.
Studies on the destruction by marine borers of fishing boats along the north-eastern Black Sea coasts of Turkey
1980 - IRG/WP 451
Marine wood-boring organisms are attacking fishing boats along the northeastern coasts of the Black Sea, Turkey. The damage and the intensity of attack of Teredo navalis L in fishing boats were studied.
O A Sekendiz, R Ilhan
An investigation of the effects of pre-steaming on the treatment of sawn spruce timber with Celcure A, a copper-chrome-arsenic preservative
1981 - IRG/WP 3150
Difficulties in the treatment of spruce using standard vacuum/pressure techniques with both water-borne and organic solvent preservatives are well known. We have evaluated the influence of steaming on treatability with a waterborne CCA preservative.
C R Coggins
Wood-destroying insects found in the Eastern Black Sea sub-region of Turkey
1982 - IRG/WP 1153
The Eastern Black Sea subregion has important forest resources. The settlement areas are scattered at the countryside. That's why a good deal of wood and timber is used in the construction of buildings without sufficient protective measures in the rural areas. In the forests and rural buildings 52 wood-destroying insect species have been specified 35 of which are new in this subregion and 14 are new in Turkey.
O A Sekendiz
Local preservation with difluoride pills: Life-time of preservative
1998 - IRG/WP 98-40127
A brief history of the situation in the Netherlands with respect to the preservation of joinery is given. Already in the eighties in the Netherlands many spruce window frames were treated with difluoride pills. One of the possible disadvantages of this kind of diffusing preservatives is the high leaching rate found in laboratory situations. The leaching rate in practice is influenced by many factors of which the condition of the paint systems and the condition of the glue in the joint are the most important. In this research the difluoride content in wood was analysed in samples which were taken from several buildings. An estimation of the remaining difluoride content leached is given. Related to these figures the remaining life of the protecting agent can be calculated. The results show that even in situations with open joints of paint damage the remaining amount of difluoride is still very high after 10 years. This suggests that in practice the leaching of difluorides is of minor importance.
W J Homan, C Blom, B W Holleboom
Water-based wood preservatives for curative treatement of insect-infested spruce constructions
1998 - IRG/WP 98-30171
On laying down sanitation measures for wooden constructions infested by wood boring insects, we must take into account static risks for the construction - and, thus, for the security of the user - as well as risks for humans and environment due to the chemical preservative compounds of the treated wood. Analyses on many roof constructions made with spruce (Picea abies L.) have revealed that Hylotrupes bajulus L. and Anobium punctatum De Geer have not the significance given to them for decennies. That often allows to replace solvant-based with water-based wood preservatives in old buildings, for the protection of humans and environment. Therefore, a method has been developed in Switzerland for testing wood preservatives with delayed curative efficacy against the house longhorn beetle. Like the European Anobium Standard EN 370 this method intends to prevent the emergence of Hylotrupes beetles. Laboratory tests with diverse water-based wood preservatives available on the market in Switzerland have shown that particularly boron and benzoylphenylurea derivatives containing products get a sufficient penetration in the wood and prevent the emergence of the beetles.
E Graf, P Manser, B Lanz
Above ground performance of CCA-treated fingerjointed lumbe
1993 - IRG/WP 93-40003
Studs made from short lengths by finger jointing are becoming more commonly used in North America. Recently Forintek has received enquiries about the performance of such material in a treated form. Treated and untreated nominal 2x4 inch² spruce-pine-fir (SPF) studs exposed above ground for 12 years in southwestern British Columbia were evaluated for evidence of decay. Despite shallow preservative penetration, which did not meet North American standards, the CCA-treated material showed no signs of decay. In contrast two of the 30 untreated samples had failed and the mean rating was 1.3 on a 0 to 4 scale. These results are encouraging for the use of CCA treated SPF as finger jointed or conventional lumber in above ground exposure.
P I Morris, G E Troughton
Treatment of dried sawn spruce and redwood building timbers with water-borne preservatives under a scheme for the quality control of the preservation and preserved wood in the Netherlands
1978 - IRG/WP 3123
Treatment of dried sawn spruce and redwood Building Timbers with water-borne preservatives under a scheme for the quality control of the preservation and preserved wood in the Netherlands. The aim of this article is to give the reader a modest description of the evaluation of fundamental research in wood preservation into a practical application.
H F M Nijman, N Burgers
Improved resistance of Scots pine and Spruce by application of an oil-heat treatment
2000 - IRG/WP 00-40162
Spruce (Picea abies L. Karst.) and Scots pine (Pinus sylvestris L.) were subject to a heat treatment which was carried out in an oil-bath. The aim was to improve the dimensional stability of the treated wood and its resistance against fungi. The bath of vegetable oil provides a uniform heat transfer at temperatures of 180°C, 200°C and 220°C and protects the submersed wood from oxygen. Heat treatment in air atmosphere was also carried out at the same temperatures for comparison. Wood treated in hot oil was more equal in its appearance than wood heated in hot air. The treatment of spruce and pine in the oil-bath resulted in a better resistance against Coniophora puteana in a lab test according to EN 113 compared to the treatment in air atmosphere. In order to achieve the wanted upgrading effect, certain changes of mechanical properties and colour must be accepted. However, the strength loss caused by the heat-treatment in oil was less severe than in air atmosphere. Since all materials and the energy used in the process originate from renewable resources, the oil-heat-treatment appears to be environmentally friendly. All in all, the heat treatment in oil might be a promising approach to upgrade wood for outdoor use.
M Sailer, A O Rapp, H Leithoff
The influence of formulation on the behaviour of LOSP's during industrial impregnation of spruce
1986 - IRG/WP 3387
Evidence is presented that the comparative behaviour of two LOSP formulations during impregnation treatment of spruce cannot be predicted purely on the basis of their physical characteristics (viscosity, surface tension and contact angle) nor on the extent of their 'passive' penetration into pine sapwood.
L D A Saunders, D M Zuvencko
Evaluation of Barrier Wrap Systems after 71 Months of Exposure
2013 - IRG/WP 13-40631
A 71 month study of the performance of booted samples in ground contact was conducted in AWPA hazard zone 4. Data indicated that excellent performance of wrapped systems, even over untreated wood, could be obtained. Instances of decay colonization or termite attack could all be attributed to some breaking of the integrity of the barrier system. Good performance for treatment below ground contact threshold was demonstrated.
H M Barnes, M G Sanders, G B Lindsey, C McIntyre
Multiple-Phase Pressure (MPP) Process: One-stage CCA treatment and accelerated fixation process. 5. Treatment of Sitka spruce and Scots pine
1999 - IRG/WP 99-40136
The suitability of the MPP Process for CCA treatment and accelerated fixation of species other than Radiata pine was assessed by pilot plant trials on UK-grown Sitka spruce (Picea sitchensis) and Scots pine (Pinus sylvestris). Pressure and vacuum kickbacks of spruce (14 l/m3) and Scots' pine (122 l/m3) were both substantially lower than that generated during treatment of radiata pine (369 1/m). Total Organic Carbon (TOC) in kickback from spruce treatment (~ 750 ppm) was approximately half that in Scots pine kickback (~ 1400 ppm), and were substantially less than TOC generated during treatment of radiata pine (~ 2000 ppm). Extent of CCA fixation (spruce: 93%, Scots pine: 97%) was similar to that obtained with radiata pine (97%). To reduce post-treatment drippage, caused particularly by the refractory nature of spruce, a modified Bethell process was found most appropriate for MPP treatment rather than modified Lowry schedules used with radiata pine. Use of hot CCA solutions did not improve penetration into spruce and some collapse (washboarding) of early wood was a feature of its treatment.
M E Hedley, K Nasheri, G Durbin
Analysing the characteristic role of moisture content for drying and fluid flow in Sitka spruce. - Part 1: The drying process of sapwood and heartwood of two different thickness of Sitka spruce using a kiln. - Part 2: Effects of moisture content on longitudinal permeability of Sitka spruce in vertical variation of the tree
2000 - IRG/WP 00-40173
The characteristic role of the moisture content in Sitka spruce (Picea sitchensis (Bong.) Carr.) that grown in the United Kingdom was examined by this study on the basis of (1) the reduction of moisture content in two different thickness of sapwood and heartwood by kiln drying process, and (2) the effects of moisture content to the longitudinal void volume filled of tanalith-C by the full-cell process from base (1 m) to apex (3 m) of the tree in sapwood zone. Accordingly, conclusions on indication of the drying process of sapwood and heartwood, and vertical variation of longitudinal flow with effects of moisture were listed separately: (1) Comparison of Drying Characteristic of Sapwood and Heartwood: The two different thickness (300x30x30 mm3 and 300x20x20 mm3) of sapwood and heartwood of Sitka spruce was dried using the suggested drying schedule in kiln. The reduction of moisture was schematically diagrammed according to sapwood and heartwood stakes. The reduction of moisture followed the same downward trend that sapwood (S) loses more moisture than heartwood (H) although the small stakes of S and H lost moisture rapidly compared with the large ones. (2) Vertical Variation of Moisture Content and Longitudinal Permeability: The 90 kiln dried defect free sapwood stakes (150x25x25 mm3) of Sitka spruce was taken from base to apex of the trees at 1, 2 and 3 m above ground level. After having the determination of moisture content in each experimental stake, the treatment was carried out by the full-cell process with CCA preservative (Tanalith-C) using a model pressure treatment plant. Significant differences observed among the tree heights from 1 to 3 m showing that slightly increases of moisture content from base to apex and conversely decreases of longitudinal void volume filled by preservative fluid.
The effects of heat treament on the specific gravity of beech and spruce wood
2003 - IRG/WP 03-40254
The effects of heat treatment on specific gravity of beech (Fagus orientalis) and spruce wood (Picea orientalis) naturally grown and intensively used in forest products industry in Turkey were studied. The wood samples were cut into 2 x 2 x 3 cm. Heat treatment was than applied to the wood samples at four different temperatures (130 °C, 150 °C, 180 °C and 200 °C) and three different durations (2 h, 6 h and 10 h) under air atmospheres. The results indicated that the specific gravity values treated by heating generally exhibited a decrease with increasing the exposure durations and temperatures compared to the untreated wood samples.
S Yildiz, Ü C Yildiz, G Colakoglu, E D Gezer, A Temiz
Changed susceptibility of the chemically and thermally degraded spruce wood to its attack by the dry rot fungus Serpula lacrymans
1999 - IRG/WP 99-10322
In buildings, some intentional or unintended situations can occur at which some wood products are exposed to aggressive chemicals and also to higher temperatures. Occasional activity of fungi on such pre-attacked wood products can be either higher or lower. This paper deals with changes in the susceptibility of spruce wood (Picea abies L. Karst.) to attack by the dry rot fungus Serpula lacrymans, in such situations, when the wood samples 8.5x8.5x120 mm3 (RxTxL) were first pre-treated with 1% water solutions of selected acids (H2SO4, CH3COOH), bases (NaOH, NH4OH) or oxidizing agent (H2O2), or they were also exposed to a higher temperature (190°C/3h). The activity of S. lacrymans was totally restricted only in one situation, if the wood was pre-treated with sulphuric acid and then exposed to 190°C. On the other hand, specimens pre-treated with ammonium hydroxide were more susceptible to bio-attack (in both situations: without or with high temperature pre-treatment effect) than sound ones.
The influence of previous anti-blue-stain preservative treatments on the fixation of CC in spruce
1997 - IRG/WP 97-30134
Freshly cut and kiln dried spruce boards were treated with 4 different anti-blue stain preservatives (ABP). After a period of 10 days allowing the samples to dry and fixate, the samples were treated with CC (chromium, copper formulation) using a vacuum pressure cycle. After impregnation the wood was steam fixed. A submersion leaching test showed differences in the leachable quantity of copper and chromium. When related to the retention of both salts after impregnation, no differences could be found between samples previously treated with anti-blue-stain preservatives and untreated samples. However, the retention of CC diminished significantly by application of quaternary ammonium compounds.
M Van der Zee, W J Homan
The effects of density on vertical variation of permeability of Sitka spruce within tree
2000 - IRG/WP 00-40156
Tree improvement of Sitka spruce is a combination of silviculture and tree breeding aimed at producing higher quality products including increased growth rate and timber yield, and wood density. It is useful to know annual ring structure and density distribution when studying the quality of wood, grading it, or determining how the wood structure affects residual flow in softwoods. Since density is a factor under genetic control, the study in this article details the effects of density on longitudinal and radial permeability of Sitka spruce from base to apex. Comparison of overall means of both longitudinal and radial void volume filled (%) suggest that longitudinal permeabilities were almost the mirror image of those for the radial permeability along the tree trunk.
Evaluation of the leach resistance and preservative efficacy of novel biocides as surface treatments applied by brush to spruce (Picea abies)
1998 - IRG/WP 98-30170
The comparative leach resistance and preservative efficacy of a number of alternative organic preservatives (available from Zeneca Specialties) and selected commercially available biocides as surface coatings to wood in Hazard Class 3 have been assessed. Two concentrations of test preservatives were applied by brush to Spruce (Picea abies), including formulation and untreated controls. A leaching program was carried out involving the immersion of the treated blocks in water for a scheduled period of time. Blocks were then subjected to biological tests to determine preservative efficacy using the basidiomycetes Coniophora puteana and Gloeophyllum trabeum in a modified EN 113 system; sapstain and mould tests were separately undertaken according to a modified EN 152 test using mixtures of Aureobasidium pullulans and Sclerophoma pithyophila, and Trichoderma harzianum and Trichoderma saturnisporium. Of the four alternative actives tested, one Zeneca development product based on Hexaconazole compared very favourably against the selected commercial biocides tested. An aqueous system based on a Zeneca penetrating aqueous polymer coupled with the Zeneca development active demonstrated favourable performance in relation to an existing solvent based product.
I M Tierney, A Bruce, D C R Sinclair, T Yeates
In ground contact field trial results of preservative treated incised and unincised spruce
1996 - IRG/WP 96-40076
Field trials of treated spruce stakes have been demonstrated that incising the stake before treatment improves the preservative uptake both for CCA and creosote. This results in a substantially extended service life for the incised stakes over the unincised stakes for preservative concentrations at commercial levels. After 24 years in ground contact the majority of incised spruce samples are sound and have provided data which indicates that the stakes treated with CCA or creosote to commercial standards could last for more than 41 years.
E D Suttie