Your search resulted in 506 documents. Displaying 25 entries per page.
Fungicidal properties of black liquor from the waste MDF board digestion in terms of wood protection
2023 - IRG/WP 23-50379
The aim of the work was to determine the fungicidal properties of black liquor as a product of the chemical digestion of waste MDF board. The resistance of wood treated with black liquor from MDF waste pulping process was compared with the resistance of wood treated with black liquor from the pulping process of a by-product from agricultural production. The control material consisted of non-treate...
B Mazela, W Perdoch, A Szulc, I Sieminska
Eradication of beetles attacking wooden historical buildings by humidity-controlled warm-air treatment
2023 - IRG/WP 23-11028
Humidity-controlled warm-air treatment is a method that kills mainly beetles that are damaging the wood. In this process, a heat-insulating and airtight covering is placed around the object building, and the temperature inside the covering is gradually raised to about 60°C, held for a certain period of time, and then gradually lowered. While maintained at 60°C, all forms of damaging insects - ad...
Y Fujii, Y Fujiwara, M Harada, H Kitahara, M Shimada, S Kondo, Y Sato, M Shimada, R Kigawa, H Watanabe, Y Komine, S Hidaka, D Ogura
Effects of phosphoric acid and diammonium phosphate treatments on the physical and fire-retardant properties of five selected Nigerian wood species
2024 - IRG/WP 24-20713
Wooden products in buildings are major sources of fuel for fire outbreaks. Effects of phosphoric acid and diammonium phosphate treatments on the physical and fire-retardant properties of wood species commonly used in buildings were evaluated. The timber species utilized in this study were sourced from the sawmill sector located in Akure, Nigeria, encompassing Brachystegia laurentii, Khaya ivorensi...
J Owoyemi, T O Akinwamide, O M Ibrahim, E A Iyiola
Studies on the treatability of selected pine species and corresponding efficacies of a new non-biocidal treatment
2024 - IRG/WP 24-20721
Wood decay caused by fungi may reduce the service life of wood in outdoor applications. Since moisture conditions in wood occur as one of the most crucial parameters for fungal decay, chemical modifications, which affect the latter, may increase the resistance of wood against such organisms. Usually, pine sapwood is easier to chemically treat than heartwood, as the former generally shows good perm...
T R da Silva Lins, L Emmerich, H Militz, P H Gonzales de Cademartoni, R J Klizke, M Pereira da Rocha
Preservative properties of boron-treated paulownia wood
2024 - IRG/WP 24-20729
This research was performed to investigate the preservative retention properties of paulownia wood treated using boric acid/borax at mass ratio of 1:1.8. Different portion of paulownia wood (top, middle, bottom) were used as a sample throughout of this study. In the treatment process, the paulownia wood was dipped in the 1% boric acid/borax solution for 1, 24, 72, 120 and 240 hours to achieve requ...
T Khadiran, M A M Abdullah, S Lipeh
Properties of thermal modified wood of Pinus pinaster, Pinus radiata and Pinus sylvestris from Galicia, Spain
2024 - IRG/WP 24-30800
This paper provides the results of a research about the properties of thermal modified wood of maritime pine (Pinus pinaster Ait.), radiata pine (Pinus radiata D. Don) and Scots pine (Pinus sylvestris L.) from Galicia, Spain, thermal treated in the industrial vacuum-heat autoclave plant of FINSA group in Galicia, Spain. These three pine wood species are used in different solid products but due the...
D Lorenzo, J Benito, J Arancon, J Crespo
Physical, durability and chemical characterization of Gmelina arborea (Roxb.) wood treated with lactic acid
2024 - IRG/WP 24-30803
The increase in demand for durable wood has drawn attention to the use of fast-grown plantation species across the globe. Chemical modification was used to treat Gmelina arborea wood with lactic acid for property enhancement. The treated samples were obtained from two different ages of 15 and 10 years and sawn into (20 x 20 x 60) mm and (20 x 20 x 20) mm for physical, durability and chemical chara...
T O Akinwamide, J M Owoyemib, E A Iyiolac
Bio-durability and weathering performances of cardanol-treated wood
2024 - IRG/WP 24-30809
Cardanol is an excellent insecticide, fungicide, and termiticide derived from thermally treated cashew nutshell liquid (CNSL) and has been extensively explored in the chemical industry and for medicinal uses. However, its potential for wood protection remains unexplored. This study aims to understand the bio-durability and weathering properties of cardanol-treated wood. The southern pine and yello...
L Liang, McDonald, A G, L Cai
Assessment of hydrophobic properties of acetylated and furfurylated Korean wood species
2024 - IRG/WP 24-30812
To increase the utilization of Korean wood species, the hydrophobic properties of the most commonly used wood species in Korea were compared according to wood modification. Pinus densiflora (sapwood and heartwood) and Larix kaempferi (heartwood) were selected as test wood species, and Pinus radiata (sapwood) was selected as the control wood species. The wood modification was performed by acetylati...
S-M Yoon, Y-S Choi, H-M Lee, Y Park, W-J Hwang, S-K Jang
Leaching and chemical redistribution of CCA components in refractory heartwood of E. nitens
2024 - IRG/WP 24-41011
Chromated Copper Arsenate (CCA) is a wood preservative widely used to protect against fungal and insect attack. The fixation mechanism of CCA involves complex chemical reactions, including the reduction of chromium (VI) to chromium (III) and the formation of insoluble complexes. Despite fixation efforts, a portion of CCA components tends to leach from treated wood, influenced by factors like wood ...
J R Vargas, L Yermán, K C Wood, T Singh
The durability and mechanical properties of 40 years old Black locust poles
2024 - IRG/WP 24-11042
This study investigates the durability and mechanical properties of 40-year-old black locust (Robinia pseudoacacia) poles harvested from a vineyard in Slovenia. Wood from these poles was compared to recently harvested black locust wood to determine possible reuse options. Visual inspection, hyperspectral imaging, and laboratory tests were conducted to assess decay, density, mechanical properties, ...
M Humar, J Malik, J Levanic, D Krzisnik, E Kerzic, B Lesar
Revealing the degradation process of Moso bamboo (Phyllostachys edulis) by different decay fungi
2025 - IRG/WP 25-11060
Moso Bamboo (Phyllostachys edulis) is the main bamboo species for engineering; however, it is highly susceptible to various fungi during use. In this study, four prevalent decay fungi, including two brown rot fungi and two white-rot fungi, were used as the test fungi to investigate the changes in structure and chemical composition of Moso bamboo samples at different incubation times in order to be...
J Xue, D Cui, M Zhou, J Cao
Multifactorial analysis of the reasons behind wood natural durability
2025 - IRG/WP 25-11065
Physical, chemical and biological properties of several wood species were investigated in order to highlight the main factors involved in wood natural durability and wood characteristic using a principal component analysis. Interaction of wood with water were evaluated using contact angle measurements to determinate wood wettability by water and wood impregnability tests with water allowing to cal...
L-F E Nkogo, M S M Mouendou, S Dumarçay, P E Engonga, F Zannini, E Gelhaye, P Gérardin
Securing Flame Retardancy in Wood: Durability After Artificial and Natural Weathering Test
2025 - IRG/WP 25-20738
The outdoor use of wood is often limited by challenges such as dimensional instability, vulnerability to fungal decay, and high flammability. Traditional flame retardant treatments improve fire resistance but suffer from significant leaching under environmental exposure, reducing their long-term effectiveness. This study introduces an innovative solution by integrating flame retardants with DMDHEU...
M Wu, L Martin, H Militz
Potential co-valorization of pyrolysis tars from five wood species form Tunisia as wood preservatives bases: Chemical compositions, antifungal and anti-termite activities
2025 - IRG/WP 25-20739
The pyrolysis of five Tunisian wood species (Ceratonia siliqua, Eucalyptus camaldulensis, Eucalyptus maidenii, Pinus pinea, and Quercus canariensis) was carried out in a custom-designed carbonisation reactor developed at the INRGREF's Wood Technology Section (Tunis, Tunisia). This process aimed to produce both char and pyrolysis by-products, particularly pyrolysis oils. The experiments were conduc...
M T Elaieb, J Valette, E Kiény, L Pignolet, S Ghariani, K Candelier
CIOL Wood - Scientific Innovations in Wood Modification for Enhanced Performance and Usage
2025 - IRG/WP 25-20743
CIOL® is a wood modification technology designed as an environmentally friendly alternative to traditional wood preservatives. Utilising a biobased formulation based on sorbitol and citric acid, CIOL® enhances wood's chemical structure, improving its durability, stability, and resistance to decay. This paper provides an overview of the advancements made in CIOL® technology, including its improv...
E Larnøy, A Treu, M Diraison, M Smith, A Audouin, P T Lewandowski, J Biørnstad
Investigation of a commercial fire-retardant additive on particleboard properties
2025 - IRG/WP 25-20755
Fire resistance of wood-based panels is in addition to mechanical and sorption properties, an important property when considering its usability for construction applications. Increased fire resistance is achieved through fire retardant addition during panel production or by spraying fire-retardant on already finished panel. A potential downside of fire-retardant addition during panel production ca...
D Jones, S Medved, M Lawther
The Impact of Drying Techniques on the Quality of Thermally Modified Wood
2025 - IRG/WP 25-30813
The wood drying technique applied before loading the dry wood into the ThermoWood® kiln may affect its properties. For this purpose, Scots pine (Pinus sylvestris) boards were first dried through three drying methods, including radio-frequency/vacuum (RF/V), mild, and moderate conventional drying, and then loaded into a ThermoWood® kiln for thermal modification at 212 °C for 3 hours according to...
M Ghorbanian Far, N Sharifi, A Nikoutadbir, A Tarmian, M Humar
Novel treatments of solid wood - studies into the use of imidazole and succinimide
2025 - IRG/WP 25-30817
Recent activities have focussed on the use of ionic liquids (ILs) in wood treatments and bioprocessing. Most ILs are based on imidazolium systems, so it was decided to investigate the potential of imidazole as a treatment, along with another heterocyclic compound, namely succinimide. Thus, modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimi...
D Jones, A Scharf, H Dernegård, J Oja, S Duarte, J Levanić, M Humar
Enhanced Termite Resistance of Low Durability Fast Growing Teak Wood by Non-Biocide Treatments Based on Chemical and Thermal Modification
2025 - IRG/WP 25-30818
Short rotation teak as a fast-growing tree can be considered as a renewable material resource for the future green economy. However, short rotation teak wood is susceptible to biodeterioration, particularly to termite attack. The objective of this work was to investigate the effect of chemical and thermal treatment on resistance of sapwood, transition wood, and heartwood of short rotation teak aga...
R Martha, K Candelier, M-F Thévenon, B George, I S Rahayu, W Darmawan, P Gérardin
The impact of common fire retardancy salts and minerals on further properties of wood
2025 - IRG/WP 25-30821
Wood has become an increasingly important construction material. To ensure fire safety, fire retardants are widely applied. Recent research focuses on environmentally friendly fire retardants with strong fixation. Phosphate-based salts like diammonium hydrogen phosphate show high fire protection potential but are highly leachable due to their good water solubility. As a newer trend mineralisation ...
T Franke, T Volkmer
Mineral-wood composites with improved fire properties and durability prepared through MgCO3-based mineralization
2025 - IRG/WP 25-30823
New mineral-wood composites that demonstrate improved fire properties and higher resistance to selected fungi have been prepared using an environmentally-friendly mineralisation process involving impregnation with an aqueous magnesium acetoacetate solution. MgCO3-based compounds are formed in situ, deep within the wood’s structure. We show that the new mineralisation method overcomes wood’s lo...
A Pondelak, N Knez, S D Škapin, M Humar, A S Škapin
Effect of Deep Eutectic Solvent Pretreatment on Properties of Densified Wood
2025 - IRG/WP 25-30824
Densified wood is preferable for structural applications because of its excellent mechanical properties and sustainability, but the fixation of its compression deformation and the prevention of water-induced mechanical deterioration remain challenging. Herein, an eco-friendly and highly efficient method was designed for producing dimensionally-stable densified wood, including deep eutectic solvent...
Y Ran, W Wang, J Cao
Properties of plasma etched super black wood
2025 - IRG/WP 25-30825
Super-black materials have very low reflectivity due to structural absorption of light. They are attracting considerable scientific and industrial attention because of their important applications in many fields including astronomy, photovoltaics, and optical science, amongst others. We have developed the first super-black material from wood by etching transverse basswood (Tilia americana L.) surf...
K J Cheng, X Xu, V A Hernandez, P D Evans
Process Development in Continuous Wood Densification and the Influence of Ionic Liquids on Set-Recovery and Mechanical Properties
2025 - IRG/WP 25-30827
The densification of wood significantly enhances its mechanical properties, making low-density species more viable for high-performance applications. However, challenges such as set-recovery (SR) and production speed hinder large-scale adoption. This study investigates continuous surface densification using a custom-built belt press and examines the effect of chemical pre-treatment with ionic liqu...
D Jones, A Scharf, B Neyses, D Sandberg