Your search resulted in 364 documents. Displaying 25 entries per page.
Improvement of wood decay and termite durability resulting from combined treatments based on borax/phenol-formaldehyde impregnation followed by thermal modification
2019 - IRG/WP 19-40871
This study determined the factors influencing the boron content after leaching of pine blocks impregnated with aqueous solution of phenol-formaldehyde (PF) resin with or without borax and subjected to heat treatment by response surface methodology. An experimental design permits to analyze the effects of heat treatment temperature (150, 185 and 220°C), curing time (5, 12, 5 and 20 hours), resin c...
S Salman, M-F Thevenon, A Petrissans, S Dumarcay, P Gerardin
Investigations into the use of Maleic Anhydride/Sodium Hypophosphite as a Wood Modification Process
2020 - IRG/WP 20-40891
The formation of crosslinked bonds between wood constituents is believed to be an effective way to stabilize wood against wet conditions. The possibility to use maleic anhydride (MA) combined with sodium hypophosphite (SHP) as crosslinking agents was studied, using Scots pine sapwood and a model compound. The modified wood showed weight gain and bulking effect after treatment and subsequent Soxhle...
I Kim, D Jones, O Karlsson, D Sandberg, O N Antzutkin, F Ullah Shah
Brief introduction to a research project on preparations of various paste formulations from boron, fluoride and copper for supplemental treatments
2022 - IRG/WP 22-30759
Wood preservatives to be used for supplemental purposes are present in various forms such as powders, liquids, rods, pastes, or gels. Boron compounds have been receiving a lot of attention in supplemental treatments since they have good mobility in wood. Application of boron compounds via internal treatments is vital to stop decay to be occurred inside the wood since large wood elements are too th...
E E Soytürk, D Bakır, E Terzi, C Köse, S N Kartal
Properties of Iron (II) Sulphate treated Norway Spruce
2022 - IRG/WP 22-30765
Exterior wood is exposed to various environmental factors that cause weathering. Weathering is important primarily from an aesthetic standpoint. However, not all parts of the building are equally susceptible to weathering. Parts exposed to moisture will discolour faster than protected parts, such as wood under roof overhangs. To achieve fast and uniform artificial greying, a surface treatment with...
B Lesar, M Humar, M Škamlec
Moisture sorption behaviour of poplar and thermally modified poplar using dynamic vapour sorption (DVS)
2022 - IRG/WP 22-40947
The moisture sorption behaviour of wood has a critical impact on service life. In Europe, softwood is mostly used to manufacture engineered wood products such as cross-laminated timber (CLT) or glue-laminated timber (GLT or glulam). Yet fast-growing and widespread tree species such as hybrid poplar with or without modification, have potential to meet the increasing demand. This study shows the moi...
X Jiang, J Van den Bulcke, L De Boever, M Minsart, A Mignon, J Van Acker
Suitability of boron preservative treatment of minor species as framing in New Zealand buildings
2023 - IRG/WP 23-30778
The inclusion of alternative species to radiata pine, predominantly exotic species, in the building code (NZS 3602) raises questions as to whether they require preservative treatment and, if so, whether they can be adequately treated using current industry processes.
Early research with boron indicated that the dip/diffusion method for green timber would give adequate preservative retention in sa...
D Page, I Simpson, T Singh
Field test methods as long-term aging – report of selective wood properties
2023 - IRG/WP 23-40962
Wood samples from a long-term field test are a valuable compendium of information about the material in the context of its aging processes. In the current work, wood samples from the round-robin test within the ECOMOD project were used as a material for the natural aging process (III and IV class of utility). The research scope was to determine selected properties of this wood which can be partial...
W Perdoch, M Benc, B Mazela, A Szulc, J Cegiela
New wood-modification process based on grafted urethane groups: Durability of carbamamylated Scots pine (Pinus sylvestris L.) wood
2023 - IRG/WP 23-40974
Substituting commonly used toxic preservatives with wood modification treatments can make the wood material less prone to water and moisture uptake. This approach favours a more sustainable protection of wood against biodegradation. In this study, Scots pine sapwood was full-cell impregnated with an aqueous solution of urea (30%), dried at 40°C for 24h, and subsequently heat-treated at 150°C for...
C-F Lin, O Myronycheva, O Karlsson, D Jones, D Sandberg
Preservative properties of boron-treated paulownia wood
2024 - IRG/WP 24-20729
This research was performed to investigate the preservative retention properties of paulownia wood treated using boric acid/borax at mass ratio of 1:1.8. Different portion of paulownia wood (top, middle, bottom) were used as a sample throughout of this study. In the treatment process, the paulownia wood was dipped in the 1% boric acid/borax solution for 1, 24, 72, 120 and 240 hours to achieve requ...
T Khadiran, M A M Abdullah, S Lipeh
Exploring bio-based chemicals in the residual stream from the thermal wood modification process
2024 - IRG/WP 24-30799
Numerous chemical-free processes have emerged in the wood processing industry to enhance the durability and optimize the service life of wooden elements exposed to exterior conditions. One such method, the hygrothermolytic modification process, patented as FirmoLin®, represents an industrial treatment for thermal modification of wood. This involves subjecting solid wood to a pressurized unsaturat...
R Herrera, W Willems, W Pajerski, A Selmanović, A Sandak
Revealing the degradation process of Moso bamboo (Phyllostachys edulis) by different decay fungi
2025 - IRG/WP 25-11060
Moso Bamboo (Phyllostachys edulis) is the main bamboo species for engineering; however, it is highly susceptible to various fungi during use. In this study, four prevalent decay fungi, including two brown rot fungi and two white-rot fungi, were used as the test fungi to investigate the changes in structure and chemical composition of Moso bamboo samples at different incubation times in order to be...
J Xue, D Cui, M Zhou, J Cao
Mineral-wood composites with improved fire properties and durability prepared through MgCO3-based mineralization
2025 - IRG/WP 25-30823
New mineral-wood composites that demonstrate improved fire properties and higher resistance to selected fungi have been prepared using an environmentally-friendly mineralisation process involving impregnation with an aqueous magnesium acetoacetate solution. MgCO3-based compounds are formed in situ, deep within the wood’s structure. We show that the new mineralisation method overcomes wood’s lo...
A Pondelak, N Knez, S D Škapin, M Humar, A S Škapin
Process Development in Continuous Wood Densification and the Influence of Ionic Liquids on Set-Recovery and Mechanical Properties
2025 - IRG/WP 25-30827
The densification of wood significantly enhances its mechanical properties, making low-density species more viable for high-performance applications. However, challenges such as set-recovery (SR) and production speed hinder large-scale adoption. This study investigates continuous surface densification using a custom-built belt press and examines the effect of chemical pre-treatment with ionic liqu...
D Jones, A Scharf, B Neyses, D Sandberg
Investigation of Impregnation Factors for Biomass-Based Phenol-Formaldehyde Resins
2025 - IRG/WP 25-41044
This study investigates the impregnation factors affecting the treatment of wood with biomass-based phenol-formaldehyde (PF) resins, such as impregnation methods, resin properties, and setting parameters like time and pressure. The goal is to ensure effective resin penetration into the wood cell wall structure, thereby enhancing wood durability and mechanical properties. Previous literature has la...
Y-C Huang, T-H Lin, P-Y Kuo