Your search resulted in 261 documents. Displaying 25 entries per page.
Quantitative determination of Chromium: A comparison of three instruments
1995 - IRG/WP 95-50053
A comparison is made between three instruments for measuring levels of chromium in the leachate of copper-chrome-arsenic (CCA) treated timber. These include an atomic absorption spectrophotometer, an inductively coupled plasma spectrometer and the RQflexâ. The RQflexâ is a new hand-held instrument which measures chromium by dipping a ReflectoquantÒ strip into the leachate and inserting the strip into the RQflexâ. Readings are determined reflectometrically following a reaction between chrome and the Reflectoquantâ strip. It provides an inexpensive and quick technique which is used in this paper to determine the degree of preservative fixation prior to the removal of CCA treated timber from drip pads of wood treatment sites. The results indicate that RQflexâ is a suitable instrument for the rapid assessment of chromium levels in rain wash off from treated timber. A comparison is given of the economics and accuracy of the instruments for measuring chromium.
S Walley, P R S Cobham, P Vinden
Chemical analysis for TBTN in LOSP-treated wood and preservative fluids
1994 - IRG/WP 94-20027
Tributyltin napthenate (TBTN) is being substituted for tributyltin oxide (TBTO) in LOSP preservative formulations because its lower reactivity/better stability allows co-formulation with synthetic pyrethroids. Better stability may reduce molecular degradation both in-service and during analysis. It was considered necessary to check whether TBTO analysis methods were suitable for use on TBTN treated wood. Five analytical methods for TBTO in wood were applied to TBTN-treated pine sapwood, and evaluated for recovery, accuracy and precision. It was found that treated wood could be oven-dried before analysis, eliminating the need to run parallel moisture content determinations. The best performing method involved extraction of TBTN from oven-dry treated wood with acidified ethanol followed by AAS determination of tin. Performance was checked on freshly-treated and aged material.
D P Wraight, M J Kennedy
Comparative studies on the species effects of wood preservatives
1989 - IRG/WP 3521
For the examination of the resistance against fungal attack, wood blocks of 3 softwood species were treated with CCA (type 3), CFK, AAC and IF-1000 independently. The wood blocks were exposed to the fungal decay with Tyromyces palustris. The degradation of the wood blocks treated with these preservatives was quite widely different among wood species examined in this study. Hem-fir treated with CCA and radiata pine treated with CFK showed less durability than the other species and other preservatives. In the case of Cryptomeria japonica, all preservatives tested gave good results. The micromorphological distribution of preservatives in cell walls was investigated with the wavelength dispersive X-ray spectrometry. The X-ray photoelectron spectroscopy was applyed for the investigation on the possibility of conversion reactions with preservatives in impregnated wood. The interaction of extractives with preservatives was examined using a conventional bioassay method for evaluations of the efficacy of wood preservatives against fungi. The concentration of Cr in the CCA treated wood was 1.5-1.6 times higher in the ray parenchyma cell walls than in tracheid walls in every wood species examined. The oxidation of wood occur during the treatments with CCA and CFK, however, there were not conspicious differences in the degree of oxidation among wood species. Although the hot water extractives themselves accelerated the mycelial growth, only the extractives of hem-fir reduced the efficacy of CCA.
K Yamamoto, S Matsuoka
Determination of boron levels in solution and in treated wood
1994 - IRG/WP 94-20041
Four methods of measuring boron levels in solutions were investigated. The methods compared included the azomethine-H method which is commonly used in soils and plant tissues, the methods outlined in the Australian Standard AS 1605 (1974) and in Wilson (1958), and the atomic absorption spectrophotometry method. Defect-free radiata pine (Pinus radiata D. Don) sapwood and wood flakes were treated to different percentage boric acid equivalent (%BAE). A slightly acidic aqueous medium was used to extract boron from the samples. Extracts were analysed using the azomethine-H and carmine methods. The recovery and coefficient of variation were calculated and discussed. Results confirmed that all methods can be used for measuring boron in solution and wood samples at the range of%BAE investigated. However, the azomethine-H method was found not only to be the simplest and quickest but the most accurate method. It was also found that wood extractives in the wood did not affect the results.
F J Romero, P Vinden, P Kho
Susceptibility of antisapstain fungicides to rain wash-off
1994 - IRG/WP 94-30046
Results of trials using miniature timber packets and simulated rain wash-off are described. Six fungicidal actives in five commercial antisapstain formulations were involved, and a clear influence of rainfall timing after antisapstain treatment was demonstrated. Differences between actives and formulations were most marked where water-spray was applied in the first hour after treatment, though even when applied after a 48 hour delay there were up to ten-fold differences in the percentages mobilised. Possible mechanisms of fixation are discussed in relation to known formulation properties. Results from a full scale trial at a sawmill are also given, and comparison made with the small-scale packet experiments. It is concluded that the results were very similar. The work is extrapolated to the 'real-life' sawmill situation, and conclusions drawn as to the likely results of heavy rain exposure at different times after fungicidal treatment of timber.
R N Wakeling, D J Cross, D R Eden, P N Maynard
Estimation of the impregnation degree of pine wood by the distribution analysis of active ions concentration in the cross-section
1999 - IRG/WP 99-20174
Samples in the form of pine wood rollers of diversified moisture content of ca. 50, 28 and 12% were impregnated with a water solution of the mixture type CCB with the use of the full-cell process. Moisture content was determined in individual layers from the girth to the pith. In the same way the concentrations of copper and chromium ions with the use of the spectrophotometric method and recalculated to the total dry mass of the preservative. Simultaneously, there was performed biological test according to EN 113 for the investigated mixture and different concentrations: 0,1; 0,16; 0,25; 0,4; 0,63; 1,0; 1,6; 2,5. The obtained fungicidal value let to determine the depth of biological resistance of impregnated wood within the impregnated zone.
K Lutomski, B Mazela
A technical note on the limitations of atomic absorption spectrophotometric analysis of copper/chrome/arsenic solutions according to BS 4072 (1974) and BS 5666: Part 3 (1979)
1988 - IRG/WP 2320
British Standards BS 4072 (1974) and BS 5666: Part 3 (1979) detail an atomic absorption spectrophotometric method for the quantitative determination of copper, chrome and arsenic in both preservative solutions and treated timber. Use of this technique during a research programme at Aberdeen has highlighted some potential inaccuracies with this method if these standard specifications are adhered to rigidly. These involve the standards specifying the production of inappropriate concentrations of solutions for calibration purposes and "unknowns" for analysis. Possible methods of avoiding these problems are discussed.
A J Pendlebury, J A Petty
Analysis of tebuconazole in wood treated with Tanalith™ E
1999 - IRG/WP 99-20158
A simple gas chromatographic method for determining tebuconazole in Tanalith™ E treated wood is described. A two step sequential extraction procedure with methanol was used. Sample extracts were analysed without cleanup or concentration using capillary column GC with thermionic specific detection. The performance of the method was assessed using radiata pine (Pinus radiata) sapwood, radiata pine heartwood, and spotted gum (Corymbia citriodora) sapwood as substrates. Recoveries from fortified samples ranged from 97% to 103%. The precision of the method was assessed by analysing a number of actual treated wood samples over a range of retention levels, which produced relative standard deviations in the range of 3% to 8%.
D E Ferlazzo
The applicability of life cyle analysis and alternative methods in the wood preservation industry
1994 - IRG/WP 94-50023
In the Netherlands, several case studies have been performed using the life cycle analysis method (LCA). This type of research is aimed at an inventory and classification (sometimes including also evaluation) of the environmental impacts of a product, from the raw material to waste stage ("cradle to grave" approach). In a LCA each environmental impact is assessed in terms of, for example, mass of raw material use (kg), energy consumption (MJ), emissions (COx, NOX, SOx, etc.) and final waste (in kg). The critical point in an LCA is the definition of comparable "functional units" for similar products made of different materials with different service lifes. As the LCA method has often proved to be very complex, lime-consuming, expensive and difficult to interpret and translate into practically usefull results, alternative methods are developed. Three methods are described and compared on the basis of various examples. It is hoped that this may be of use as a starting point for further discussion on the suitability of applying the LCA on (preservative treated) timber products.
P Esser, J Cramer
Utilization of curcumin for detection of presence of boron in wood
1982 - IRG/WP 3191
It has been shown that curcumin is not a reliable reagent for detecting boron in wood that has been attacked by fungi
Results of chemical analyses in the field of wood preservation in the Bundesanstalt für Materialprüfung
1973 - IRG/WP 321
The results of qualitative and quantitative chemical analyses of wood preservatives are often the basis for evaluating the various works in the field of wood preservation. In the past 10 to 15 years a number of such works was carried out in the Bundesanstalt fur Materialprüfung, Berlin-Dahlem, dealing with the identification and effectiveness of wood preservatives and with methods of wood preservation. Fundamental realisations were made which will be summarised below. It seems advisable to differentiate between inorganic and organic chemical wood preservatives and methods of analyses. These are two distinct fields which differ also with regard to the analytical techniques applied.
H J Petrowitz
Modelling of PCP migration in the environment: Feeding the models with laboratory data
1993 - IRG/WP 93-50001-08
In 1989, Hydro-Québec began a study program on pentachlorophenol (PCP) to ensure safe use of the product at all stages. One of the aspects of the study is the creation of a predictive system for evaluating the behavior of PCP and oil migration from wood poles to the environment. This system comprises four mathematical models for predicting PCP and oil migration in and on the surface of the pole, in soil and in groundwater, and for predicting runoff. Laboratory experiments aimed at quantifying and supplying the input for each model have been designed. A method of analyzing both PCP and oil in water. wood and soil has been developed. The radial and longitudinal distributions of PCP and oil concentrations have been established for several combinations of wood species and treatments. Laboratory setups and preliminary results are presented.
A Besner, P Tétreault, R Gilbert
Penetration analysis of two common bamboo species - borak and jawa of Bangladesh
2002 - IRG/WP 02-40247
Preservative treatment of two bamboo species, namely borak (Bambusa balcooa Roxb.) and jawa (Bambusa salarkhanii Alam) was carried out with chromated copper boron (CCB) preservative by dipping method. The variation in preservative penetration between the two different species was determined. It was found that preservative penetrates into borak quicker than into jawa and easier into air-dried bamboo than into green one.
M O Hannan, A K Lahiry, N M Islam
The leaching of copper, chrome and arsenate from CCA-impregnated poles stored for ten years in running water
1978 - IRG/WP 3122
There is no evidence to indicate that the chromium and copper components are leached from the outermost 5 mm of sapwood in poles impregnated with Boliden K33 and Tanalith C and stored in running water for ten years. The arsenic component, however, seems to be leached out during the first few months to an extent of about 20% of the initial amount. The leaching time is dependent on the preservative used.
F G Evans
Finite element analysis of boron diffusion in wooden poles
2003 - IRG/WP 03-40263
The problem of describing the migration of dissolved boron in wood is treated with special reference to the commonly used remedial treatment of wooden poles. The governing equations are derived and discussed together with some of the material parameters required. The equations are solved by the finite element method and finally, results showing the effect of different treatment strategies are presented.
K Krabbenhøft, P Hoffmeyer, C G Bechgaard, L Damkilde
Conforming to european standards for preservative-treated timber: Specifying with confidence
2000 - IRG/WP 00-20194
A four-year collaborative study between four industrial partners and BRE has assessed timber treated by current UK industrial practices in the light of current European Standards. Data were collected for CCA and creosote treated timber components, and compared with the requirements laid out in EN351-1 and -2. A number of difficulties were encountered that have been described in previous IRG papers (98-20150, 99-20156), such as the poor reproducibility of chemical analyses and variable timber density. This paper describes the conclusions of our collaboration, focusing on the application of the findings and how to overcome any difficulties encountered. The data collected allowed the calculation of figures that have been submitted for inclusion into the UK's proposed national code for preservative-treated timber (DD239). An example is the recommendation of new minimum retention figures for creosote-treated commodities. This paper describes the factors that will enable UK specifiers to use the European Standards with confidence and greater understanding of how they map onto traditional methods of specification. In addition valuable lessons have been learnt applicable to the industry world wide.
E D Suttie, R J Orsler
The effect of treatment method on CCA efficacy in Corsican pine
1992 - IRG/WP 92-3723
As part of a study into the influence of application method on preservative efficacy Corsican pine (Pinus nigra) samples (50 x 50 x 400 mm³) were treated with a CCA formulation using Bethel, Steam/Bethel or Lowry processes. Full penetration of the preservative at a gross level was confirmed using a copper disclosing reagent. The preservative was allowed to fix and then samples were converted into mini-blocks (30 x 10 x 5 mm³) to produce decay test samples from various locations within the larger samples. After leaching, sets of replicate mini-blocks were exposed to the decay fungi Coniophora puteana FPRL 11E, Coriolus versicolor FPRL 28A, and Chaetomium globosum FPRL S70K. Equivalent sets of leached blocks, were analysed using atomic absorption spectrophotometry to determine preservative concentration and balance. The results of this study have been used to assess the effect of preservative application method on CCA efficacy. They also indicate how treatment method affects the distribution of the active elements of the preservative throughout the treated wood.
P R Newman, R J Murphy
Electron microscopic detection and chemical analysis of three-lamellar structures in wood-destroying fungi
1984 - IRG/WP 1240
In the course of transmission electron microscopical investigations of pine wood decay by various brown- and white-rot fungi extracellular three-lamellar structures (TLS) formed by the fungi were found in specimens stained with ruthenium red. These structures occured in the lumen of the wood cell surrounding the hypha at the outermost layer of the fungal cell wall. In the course of the investigations these structures were also detected in fungi cultivated with glucose on a rotary shaker, where they showed forms similar to tubuli and vesicles. The three-lamellar structures formed by the white-rot fungus Sporotrichum pulverulentum, which were contained in the outermost cell wall layer, were isolated by disintegration of the fungal pellet and subsequent digestion of the fungal cell wall by snail enzyme. It was found that these structures are resistant to the enzymatic digestion and are composed of 80 to 90% carbohydrates, mainly consisting of glucose monomeres, 5 to 10% proteins, containing 5 fractions with molecular weights between 30000 and 200000, and finally 5 to 10% lipids which do not contain any phospholipid.
R Foisner, K Messner, H Stachelberger, M Röhr
Detection of defects in standing poles by X-ray techniques
1980 - IRG/WP 2132
The application of X-ray techniques to wood pole inspection procedures has been evaluated. Internal defects were accurately identified using X-ray inspection methods. These methods and their possible influence on the safety and economic aspects of wood pale utilization are discussed.
W D Gardner, R S Johnstone, W Pitt
Collaborative field experiment: Analysis of copper and chromium in stakes of the four reference timbers
1982 - IRG/WP 3213
The stakes analysed belong to the Swedish set of the four reference timbers of the collaborative field experiment (Document No: IRG/WP/367). Before the field exposure 60 mm were cut off the end of each stake. This was done in order to be able to carry out chemical analyses as well as different types of testing. Some of the material has been used in softrot tests (Document No: IRG/WP/1151).
Observations on the failure of anti-sapstain treated timber under non-drying conditions
1990 - IRG/WP 1437
A range of bacteria and yeasts were isolated from antisapstain treated timber and fresh sawdust. Solution samples containing 100 ppm of TCMTB in a nutrient medium were inoculated with these organisms and incubated at 25°C for 5 days. The levels of TCMTB remaining in solution were determined by HPLC analysis after this time. Results indicated high losses of active ingredient for a range of organisms. These results suggest that active biodetoxification of organic biocides could occur in a short period of time during storage of antisapstain treated timber under favourable conditions. The implications of these results are discussed.
G R Williams
Comparative studies on the distribution of lignin and CCA elements in birch using electron microscopic X-ray microanalysis
1987 - IRG/WP 1328
The microdistribution of metal preservatives in treated wood has received considerable research over the last two decades. Despite this, little effort seems to have been made to try and correlate the distribution of CCA elements with respect to naturally occurring wood cell wall components in wood. In the present preliminary study an attempt is made to relate the distribution of lignin in-situ with that of CCA elements. For the study matched samples of Betula verrucosa were first either mercurized to specifically label the lignin or vacuum impregnated with a commercial 2% K33 CCA preservative solution. Thereafter using SEM-EDXA, the relative distribution of labelled lignin and CCA elements were compared for both different cell types and cell wall regions. Results showed the relative microdistribution of CCA to follow closely that of the lignin distribution. Regions showing high lignin levels showed high CCA levels and vice-versa. Highest CCA and lignin levels were recorded in the vessel, fibre and ray middle lamella cell corners regions while the lowest levels were detected in the fibre (S2) secondary walls. Both the low lignin level (and syringyl type) and CCA uptake in fibre S2 walls would seem in close agreement with the known high susceptibility of these elements to soft rot attack in both treated and untreated birch. Comparisons made between the lignin content of the S2 layer for birch fibres and other known soft rot resistant species (e.g. Alstonia scholaris) showed great differences, with the latter showing much higher lignin (ca 3x) levels.
G F Daniel, T Nilsson
Ultrastructural and TEM-EDAX studies on the degradation of CCA treated radiata pine by tunnelling bacteria
1985 - IRG/WP 1260
An ultrastructural study was carried out on bacterial attacked Pinus radiata stakes treated with a high level (24.7 kg/m³) of Tanalith NCA preservative. The purpose of the investigation was to determine whether the organism possessed intracellular and/or extracellular detoxification mechanisms in order to overcome the high levels of copper, chrome and arsenic present within the wood fibre walls. Correlated T.E.M. and T.E.M.-EDAX studies showed most of the preservative elements to remain outside the bacteria associated with bacterial tunnel wall and cross-wall extracellular secretions. T.E.M.-EDAX showed the levels of preservative elements present in the tunnel walls and cross walls to often greatly exceel that recorded in neighbouring S2 cell wall regions, while studies on the bacteria showed that only copper and very low levels of chromium and arsenic had entered the cells. Observations suggested that the metals found within the cells were associated with electron-dense deposits or inclusions within the nuclear region or cell cytoplasm, the deposits often containing high levels of phosphorus and calcium together with lesser levels of other cations. The study also provided evidence for the direct visualisation of CCA preservative elements within fibre walls using T.E.M. without any form of secondary chemical enhancing, and in addition, considerable new information on the nature and structure of the single celled, Gram-negative, motile bacteria involved in the decay.
G F Daniel, T Nilsson
Collaborative soft rot tests: 2nd interim report
1975 - IRG/WP 258
J G Savory, J K Carey
A bibliography of organic solvent-based wood preservatives
1973 - IRG/WP 322