IRG Documents Database and Compendium


Search and Download IRG Documents:



Between and , sort by


Displaying your search results

Your search resulted in 142 documents. Displaying 25 entries per page.


Fouling and Boring Organisms Deteriorating Various European and Tropical Woods at Turkish Seas
2010 - IRG/WP 10-10741
This study aims to investigate the diversity of fouling and boring organisms damaging wood material at Turkish coasts. Trials were carried out at six harbour sites throughout the seas surrounding Turkey. Wood samples were hanged down at a depth of six meters in the sea, for a period of one year. Identification of the organisms obtained from wood plates revealed the presence of five wood borer and 26 fouling species. Iskenderun harbour had the highest boring organism diversity (five species), followed by Trabzon, Finike harbours (three species) and Bandirma, Eregli and Alaçati harbours (two species). The two molluscan boring species, Teredo navalis and Lyrodus pedicellatus were present at all harbour sites, but Nototeredo norvegica occurred only at Trabzon and Iskenderun harbours, Bankia carinata only at Iskenderun harbour, and the crustacean wood borer Limnoria tripunctata at Finike and Iskenderun harbours. All native tree species, except for the olive, were significantly impacted from fouling and boring organisms.
S Şen, H Sivrikaya, M Yalcin, A Kerem Bakır, B Öztürk


The anatomical determination of wood samples found in the “Fürstengräber” from Lübsow (Poland)
2018 - IRG/WP 18-10930
The paper presents the results of anatomical research identifying three wooden fragments from the “Princes Graves” (“Fürstengräber”) in Lübsow, Poland. The research demonstrates that the wooden fragments are typical of wood harvested from European forests. The physicals conclusions are important for the research of Jan Schuster, from the University of Lodz, Institute of Archeology, Poland. Investigation and identification of the contents of the Six Elite Graves (“Elitegräber”) are eminent for an understanding of social mores and customs of the first and second centuries in Europe.
J Schuster, W Unger, T L Woods


Proposed method for out-of-ground contact trials of exterior joinery protection systems
1981 - IRG/WP 2157
Methods for testing the efficacy of preservative treatments for exterior joinery are described using the format of a European Standard. Commercially used treatments applied to jointed test units (L-joints) which are then protected by conventional finishes are exposed to normal outdoor hazards out of ground contact. Assessment is made a) by determining eventual failure through decay and b) by destructive examination of replicate treated and untreated units, after increasing time intervals, rating comparative performance in terms of wood permeability increase and the progress of microbial colonisation.
J K Carey, D F Purslow, J G Savory


How to Document the Performance of Super-Critical Treated Wood in above Ground Situations?
2005 - IRG/WP 05-20316
The paper presents practical experiences from the preparation of a new preservative treated wood product for introduction to the market. The product in question is Superwood™, which is treated with organic biocides using CO2 in a supercritical state as a solvent. The question is how to evaluate the performance of a new product such as Superwood™ in order to get an acceptance on the market and fulfil the formal requirements. In the European Union countries, the EN 599-1 is the standard that needs to be complied when approving a new product for the market, but it only focuses on the toxic limit against representative decay fungi according to EN 113. However, decay test, above ground and other forms of field tests are optional, this is not in line with the traditional test philosophy in the Scandinavian countries. The open question is to which extent treatment to the level of the toxic threshold value also ensures a long service life and expected performance of the treated commodity. Superwood™ is evaluated using a strategy, in which basic laboratory tests are done to get the toxic value (according to EN 599-1) and in addition a number of field tests are done including accelerated testing in the tropics. These tests are focussed on the evaluation of the performance criteria such as durability and service life and maintenance requirements. These questions must be answered by the producer without having a full record of performance test for their new products. A short status on the test performed on super-critical treated wood (Superwood™) is presented. Based on a comparison between field test in Scandinavia and in the tropical Malaysia a service life of more than 25 years for a specific supercritical treated product is estimated. It is stated that the existing European standardisation system is insufficient when it comes to service life prediction. A number of important questions need to be addressed by the European standardisation system as soon as possible because the market and the public opinion change quickly due to environmental concern.
N Morsing, A H H Wong, F Imsgard, O Henriksen


European Biocides Directive (98/8/EC): Programme for systematic examination of all active substances of biocidal products on the market on May 13, 2000 Article 16(2)
2001 - IRG/WP 01-50166-03
PPT-Presentation
K Rasmussen, A B Payá Pérez


Wood preservation in Lithuania
2004 - IRG/WP 04-30363
This article is intended to give basic information on wood preservation activities in Lithuania and the main actors in wood preservations practice and research. Currently the main actors in practical Lithuanian wood preservation activity are enterprises of wood preservation industry united by the Lithuanian Wood Preservation Association. The most intensive activity in wood preservation practice and research started after 2001. The only active institution in wood preservation research currently is Lithuanian Forest Research Institute with 2 running projects. Lithuanian University of Agriculture and Kaunas University of Technology are active in standardization and have potential to start research. Main obstacles for future development of wood preservation research are: insufficient interest of industry in research and lack of skilled scientists.
J Saladis


Report on the activities of the European Standardization Committee CEN/TC 38 'Methods of Testing wood preservatives'
1980 - IRG/WP 279 E
G Castan


Thermal treatment of wood: European Processes and their background
2002 - IRG/WP 02-40241
Recent efforts on thermal treatment of wood lead to the development of several processes introduced to the European market during the last few years. The total production capacity of heat treated wood in 2001 is estimated as approx. 165.000 m3. In the paper the different heat processes are presented. The general technology as well as scientific data on the chemical transformation of the cell wall polymers, on the biological performance, on the physical and mechanical properties of the treated wood are presented and discussed
H Militz


Bioaccumulation of pentachlorophenol in rainbow trout and zebra fish muscles
1986 - IRG/WP 3372
The bioaccumulation of pentachlorophenol in Rainbow Trout and Zebra fish has been evaluated by partition coefficient n-octanol/water determination at ph 7 and measured in vivo according to the OECD guidelines and the European directive 79/831/EEC. The obtained results confirm the low bioaccumulation potential of this product in aquatic organims.
J C Palla, M Dion


European standardization for wood preservation
1988 - IRG/WP 2321
G Castan


European standardization for wood preservation
1989 - IRG/WP 2335
G Castan


Interspecific variability of European oak durability against white rot fungi (Coriolus versicolor): Comparison between sessile oak and peduncle oak (Quercus petraea and Quercus robur)
2001 - IRG/WP 01-10393
The knowledge of wood natural durability against biologic predators enable its external use. The resistance of European oak wood was reported like durable according to the EN 350-2. However, some individuals may contain high durable wood. Our research was focused to understand this variability in oak population that represent the first french species (4.1 millions of ha). Natural durability of European oak heartwood (Quercus petraea and Quercus robur) against white rot fungi (Coriolus versicolor) was tested according to european standard EN 113. The experimental material consists in 23 oaks robur and 26 petraea oaks sampled from 9 French regions. For each tree, 3 twin samples were taken off from heartwood situated at 1.30 m from the bottom of the tree. Different effects were tested by hierarchic variance analysis: "species", "forest within species" and "tree within forest". The tree effect is very significant for biologic natural resistance. Variability between species was also demonstrated. Although the species effect is significant, it's relatively weak compared with tree differences (it was declared significant 5%). Durability classification was determined according European standard EN 350-1. 69.2% of petraea oak trees are classified as high durable, 19.2% durable, 7.7% moderately durable and 3.8% slightly durable. In the case of robur oak 91.3% of trees are classified as high durable and 8.7% durable.
N Ayadi, B Charrier, M Irmouli, J P Charpentier, C J Allemand, F Feuillat, R Keller


CEN Draft (38 N 460E) Standard: Test method for determining the protective effectiveness of a preservative in the marine environment
1986 - IRG/WP 4132
This European Standard describes a marine test method which provides a basis for asseasing the effectiveness of a wood preservative used to prevent attack of timber in sea-water by marine borers. The method is only suitable for testing preservatives which are intended to prevent attack by marine wood boring organisms of treated timber for use in more or less permanent contact with sea-water. It is not suitable for assessing the effectiveness of preservatives against micro-organisms. The main objective of the method described is to evaluate the relative effectiveness of a wood preservative applied by vacuum/pressure impregnation. For this reason permeable timbers are used throughout so that the protective efficacy of various retentions of the preservative can be determined. However, it is recognized that modifications of the method may be used for other purposes, e.g. to determine the relative efficacy of a preservative treatment or to determine the natural durability of the heartwood and sapwood of a selected timber species. The method is primarily intended for testing in temperate waters where Teredine and Limnoria borers dominate. However, it is also capable of being used in tropics where attack by Pholads and specific Crustacean borers may be very destructive. It has to be considered that the test has to be run for a minimum period (usually for 5 years or until the point of failure) before any interpretation of the results can be made. Variations in the test conditions can be expected from one test site to another depending on temperature, salinity, population density of the various borer species etc. This will inevitably influence the general rate of attack. However, by comparing the results obtained for samples treated with the test product with those obtained with a reference preservative and those obtained with untreated control samples, the relative protective effectiveness of the product tested can be evaluated.
G Castan


In-ground performance of two formulations of chlorothalonil after five years of exposure at three test sites in Australia
1996 - IRG/WP 96-30101
Sapwood specimens of Pinus radiata D. Don and Eucalyptus regnans F. Muell. were each treated to three retentions of each of two preservative formulations (chlorothalonil in oil; chlorothalonil plus chlorpyrifos in oil) and installed in-ground at three field test sites in Australia. Specimens were treated with each formulation to achieve 3.2, 6.4 and 12.8 kg/m³ of chlorothalonil a.i. and 3.2 + 0.2, 6.4 + 0.4 and 12.8 + 0.8 kg/m³ of chlorothalonil plus chlorpyrifos a.i. For comparison, specimens of each timber species, treated to a commercial in-ground retention of a copper-chromium-arsenic (CCA) formulation, were also installed. Treated specimens (including controls) have been rated for their condition annually for attack by subterranean termites and fungal decay using a scale ranging from 4 (sound) down to 0 (failed). After five years of exposure, mean termite and decay scores for replicate test specimens at each site reveal that the performance of all three retentions of each formulation, particularly the two highest retentions, is comparable to CCA.
J W Creffield, T L Woods, N Chew


Studies on the infestation behaviour of the powder-post beetle Lyctus brunneus (Steph.) and its physical control in the wood yards of the Caspian forests of Iran
1985 - IRG/WP 1271
Lyctus brunneus (Steph.) is a pest which has not been previously thoroughly studied in Iran. It severely attacks Iranian hardwoods, especially those used in wooden houses and that have not been treated. Research work was necessary to determine the natural resistance of the most important timber species in Iran against this insect.
P Niloufari


European standardization for wood preservation
1990 - IRG/WP 2359
G Castan


The biocides directive
1995 - IRG/WP 95-50040-25
G Wilson


CEN Draft Standard (38 N 460F): Méthode d'essai pour determiner l'efficacité d'un produit de préservation du bois en milieu marin
1986 - IRG/WP 4132 F
G Castan


Conforming to european standards for preservative-treated timber: Specifying with confidence
2000 - IRG/WP 00-20194
A four-year collaborative study between four industrial partners and BRE has assessed timber treated by current UK industrial practices in the light of current European Standards. Data were collected for CCA and creosote treated timber components, and compared with the requirements laid out in EN351-1 and -2. A number of difficulties were encountered that have been described in previous IRG papers (98-20150, 99-20156), such as the poor reproducibility of chemical analyses and variable timber density. This paper describes the conclusions of our collaboration, focusing on the application of the findings and how to overcome any difficulties encountered. The data collected allowed the calculation of figures that have been submitted for inclusion into the UK's proposed national code for preservative-treated timber (DD239). An example is the recommendation of new minimum retention figures for creosote-treated commodities. This paper describes the factors that will enable UK specifiers to use the European Standards with confidence and greater understanding of how they map onto traditional methods of specification. In addition valuable lessons have been learnt applicable to the industry world wide.
E D Suttie, R J Orsler


Selective adsorption of antisapstain actives from two aqueous suspensions, and movement of actives into wood
1996 - IRG/WP 96-30103
Green-off-saw rough sawn Pinus elliottii (slash pine) boards were dipped in aqueous suspensions of two antisapstain formulations, NeXgenâ and Busanâ Sap Stain Preventative (Busan 1009), at three product concentration levels. Concentrations of active ingredients (NeXgen: CTL (chloro-thalonil) and MTC (methylene bisthiocyanate); Busan 1009: TCMTB (2(thiocyanomethylthio)-benzothiazole) and MTC) were monitored with respect to the amount of material dipped. Selective adsorption (removal of actives from the suspension at greater than simple volumetric transfer rates) varied with formulation and active ingredient, and increased with decreasing product concentration. Movement of active ingredients into dipped boards was monitored for 30 days after dipping. Mobility order was MTC >> TCMTB > CTL. Surface depletion characteristics were obtained for each active ingredient.
M J Kennedy, T L Woods


A combination of chlorothalonil and chlorpyrifos for more effective wood preservation
1995 - IRG/WP 95-30067
Chlorothalonil (tetrachloroisophthalonitrile) is a highly effective fungicide and wood preservative. Chlorpyrifos (O,O-diethyl O-(3,5,6-trichloro-2-pyridinyl)phosphorothioate) is an insecticide and is not generally considered to possess significant antifungal activity. However, a review of the literature revealed that chlorpyrifos effects in various ways the activity of microorganisms and is even registered for control of a fungal plant disease. Laboratory and field research trials were designed to study the wood preservative effectiveness of combinations of chlorothalonil plus chlorpyrifos. In some tests the antifungal activity of the insecticide chlorpyrifos was confirmed; however in a fungus cellar test, chlorpyrifos by itself provided little protection. In laboratory termite testing, chlorothalonil was sufficiently effective that in most experiments the addition of chlorpyrifos had little effect, while in field tests the combination consistently outperforms chlorothalonil alone. In tests against various marine borer species, the combination of chlorothalonil plus chlorpyrifos proved superior to chlorothalonil alone. The synergy of chlorothalonil plus chlorpyrifos is demonstrated in field stake tests, where after eleven years in Florida the combination has given superior performance over stakes treated with pentachlorophenol or chlorothalonil alone. Chlorpyrifos alone provided little protection against decay in these field stake tests. Chlorpyrifos is a useful additive to wood preservative fungicides, conferring additional protection against both decay fungi and wood destroying insects.
T L Woods, P E Laks, T C Blewett, R D Fears


Draft Business Plan of CEN/TC 38 - Durability of wood and wood-based products - Introduction
2000 - IRG/WP 00-20207
CEN Technical Committees and Business Planning. The extension of formal business planning to CEN Technical Committees (CEN/TCs) is an important measure which forms part of a major review of business processes (known as 'Optimization'). The aim is to align the CEN work programme with expressed market needs and to ensure the adequate resourcing of projects through their development stages in the CEN/TCs. Your role in the implementation of the Business Planning concept will contribute significantly to the overall effectiveness of European standardization. We express our sincere appreciation and thanks for your time in reviewing this Business Plan.
R Hüe


Wood preservation in East European countries
1989 - IRG/WP 3527
The paper discusses the main problems of wood preservation in Bulgaria, Czechoslovakia, German DR, Hungary, Poland, Rumania and the USSR. The main types of wood preservatives produced have been presented, as well as the state of standarization to test their properties. There have been considered methods of wood treatment in use and application range of treated wood.
J Wazny


A wood preservative for the future: Copper dimethyldithiocarbamate
1994 - IRG/WP 94-30045
The development of a new wood preservative, copper dimethyl-dithiocarbamate (CDDC) is reviewed in this paper. CDDC is formed in situ by dual pressure treatments. Laboratory and field efficacy trials, physical and chemical properties of the preservative solutions and treated wood, and plant handling characteristics of the system are examined.
D K Stokes, M H Freeman, T L Woods, R D Arsenault


Evaluation and approval of wood preservatives. Unification of European requirements
1988 - IRG/WP 2310
This paper reviews the current activities within the European Homologation Committee for Wood Preservatives (EHC) towards unification of the requirements on evaluation and approval of wood preservatives in Western European countries.
J Jermer


Next Page