IRG Documents Database and Compendium


Search and Download IRG Documents:



Between and , sort by


Displaying your search results

Your search resulted in 151 documents. Displaying 25 entries per page.


Radio frequency heating times for sterilization radiata pine solid piles
2017 - IRG/WP 17-40815
In this work was sterilized wood packaging material of radiata pine, stacked as solid piles without stickers, for determining the heating times using radiofrequency treatment. The experiments were performed in a radio frequency semi-industrial equipment. The results showed that the radio frequency heating times increases with wood volume and that radio frequency treatments were faster than conventional vapour heat treatment.
H Esquivel, V Sepúlveda, J Torres, L Salvo, R A Ananías


Sterilization of mango wood (Mangifera indica L.) without heat
1995 - IRG/WP 95-30065
Researches revealed that boric acid can play an important role for sterilizing wood instead of heating. Wet (green) mango boards (Mangifera indica L.) were pressure treated in treating cylinder at initial vacuum of 508 mm Hg for 15 minutes and impregnation pressure of 7 kg/cm² for 4 hours with 5% solution (w/v) of 1:1:1 commercial grade (95% pure) sodium dichromate, copper sulphate and boric acid. Penetratons of copper sulphate and boric acid were examined by using standard reagents. Copper sulphate penetrated superficially but boric acid penetrated completely through the boards. In most hazardous conditions during rainy season the treated boards were saved like heatsterilized boards from the attack of decay fungi and insects. Untreated boards (control) were found decayed and damaged within three months with the decrease of strength significantly. Where heatsterilization and kiln-drying are practically impossible during rainy season, wet timbers can be stored after impregnating those with at least 2% solution (w/v) of boric acid which diffuses through wet wood successfully and can protect wood from decay fungi, and wood destroying borers.
A K Lahiry


Kiln drying of poles as a means of solving the problems of pre-treatment decay in poles
1985 - IRG/WP 1263
The concept that pre-treatment decay can cause wide variation in the treatability of wood and especially wood poles has caused much discussion and debate in wood preservation circles. Yet it seem only logical that if decay has effected the strength characteristics of the wood and caused a differential moisture content in the wood the treatment of the end product will be highly variable and the longevity of the product will be unpredictable. Quite simply the one proven solution to the problem seems to be to artificially season the wood, usually by kiln drying, prior to treatment. This paper briefly reviews 1984 observations of the success of one treating operation in the Republic of South Africa in reducing the deterioration found during proof loading of all the poles produced. A literature survey is included to review the research accomplished to date to show that the results are truly valid. It is hoped that this paper will serve as a literature reference to other researchers in this subject and that they will contribute their findings to the work of the working group on pre-treatment decay in wood.
J A Taylor


Treatment groups and remedies for CCA treated hardwood and softwood poles
1999 - IRG/WP 99-40142
Different hardwood and softwood species from Bangladesh and Bhutan was investigated regarding density, green fiber stress, natural durability of heartwood and CCA treated sapwood, CCA treatability grades, sapwood thickness, and kiln-drying properties for long term use as electric poles. These properties along with the past service records for nineteen years, separated ten heardwood and five softwood species into four treatment groups. The treatment groups are very specific for specific timber species and adequate for equivalent requisite service life for tropical and subtropical climatic conditions without premature failure like in the past.
A K Lahiry


Proposal for further work on accelerated ageing
1988 - IRG/WP 2314
M-L Edlund


Thermal treatment of wood: European Processes and their background
2002 - IRG/WP 02-40241
Recent efforts on thermal treatment of wood lead to the development of several processes introduced to the European market during the last few years. The total production capacity of heat treated wood in 2001 is estimated as approx. 165.000 m3. In the paper the different heat processes are presented. The general technology as well as scientific data on the chemical transformation of the cell wall polymers, on the biological performance, on the physical and mechanical properties of the treated wood are presented and discussed
H Militz


Durability of pine modified by 9 different methods
2004 - IRG/WP 04-40288
The decay resistance was studied for pine modified by nine methods of wood modification: 1) Acetylation, 2) Treatment with methylated melamine resin (MMF), 3) Acetylation followed by post-treatment with MMF-resin, 4) Thermal modification, 5) Furfurylation, 6) Maleoylation (using water solution of MG or ethanol solution of maleic anhydride), 7) Succinylation, 8) NMA-modification and 9) modification with reactive linseed oil derivative (UZA), Wood blocks of Scots pine (Pinus sylvestris L.) sapwood were modified in pilot plants. Methods 1-5 were performed by the authors at Chalmers University of Technology or at BFH in Hamburg. Methods 5-9 were part of a European research project (the Chemowood project, FAIR-CT97-3187) and therefore each of these modifications was performed by the project participant responsible for the method. For laboratory testing in TMCs (modified European standard ENV 807) and pure basidiomycete culture bioassays, smaller test specimens were cut from the modified wood blocks. Most of the modification methods were applied on test specimens for marine field testing (EN 275) and some methods to produce mini-stakes for field tests in five Swedish fields. Some modification methods result in modified wood with poor durability, whereas other methods (acetylation, furfurylation and MMF-treatment) seem to provide excellent resistance to microbial decay.
M Westin, A O Rapp, T Nilsson


Corrosion of fasteners in heat-treated wood – progress report after two years’ exposure outdoors
2005 - IRG/WP 05-40296
The corrosion of common fastener materials now in use - mild steel, zinc-coated steel, aluminium and Sanbond Z-coated steel – has been evaluated after two years’ exposure outdoors in untreated and heat-treated spruce (Picea abies) respectively. Spruce from South-western Sweden was used. The heat-treatment was carried out in Finland according to the ThermoWood process at a maximum temperature of 220 °C for five hours. The results so far show that the corrosion of fasteners in heat-treated wood according to the particular specification is more severe than in untreated wood. Mild steel and zinc-coated steel has been most susceptible. Stainless steel is hardly attacked at all.
J Jermer, B-L Andersson


Accelerated ageing of preservatives in treated wood
1988 - IRG/WP 3476
New preservatives are tested in the laboratory and often in field tests before they are used commercially. Some preservatives, however, tested in the laboratory do not show the expected stability when used in service. The differences between laboratory tests and practical use can never be completely eliminated but must be minimized as far as possible by relevant testing methods. Studies of the effect of different accelerated ageing procedures on the chemical degradation and the wood preserving capacity of six different fungicides or combinations thereof have been carried out. Chemicals tested were tributyltinoxide (TBTO), tributyltin naphthenate (TBTN), furmecyclox, benzalkoniumchloride (AAC) + guazatin and pentachlorophenol. The ageing procedures included exposure of test specimens in a wind tunnel (according to EN 73), in an oven at 40°C, 60°C and 70°C, leaching (according to EN 84) and combinations of these procedures. The influence of the different accelerated ageing procedures on the chemical degradation and toxic effect of different fungicides was obvious and, for some procedures and chemicals, comparable with experiences from practice.
M-L Edlund, B Henningsson, B Jensen, C-E Sundman


Collaborative soft rot tests: Proposals for a standardized soil burial test
1971 - IRG/WP 201
A F Bravery


Proposals for a vermiculite burial soft rot test method
1980 - IRG/WP 283
J G Savory, J K Carey


Collaborative soft rot tests: Summary of comments on 'Proposals for a standardized soil burial test'
1971 - IRG/WP 202
J G Savory


Plastic-coated marine piling in Los Angeles Harbour
1984 - IRG/WP 4105
G Horeczko


Standardisation of tests of toxicity of preservatives to soft rot fungi
1978 - IRG/WP 2119
J G Savory


Developments in wood preservation processing techniques in New Zealand
1980 - IRG/WP 3143
P Vinden, A J McQuire


Evaluation of wood treated with copper-based preservatives for Cu loss during exposure to heat and copper-tolerant Bacillus licheniformis
1999 - IRG/WP 99-20155
Copper-based wood preservatives need to be effective against exposure to all types of microorganisms. Wood treated with six copper-based preservatives was exposed to 121°C and 20 psi pressure for 15 minutes under standard autoclave conditions and the copper-tolerant bacterium, Bacillus licheniformis CC01, for 10 d at 28°C and 150 rpm. Sixteen to 37 percent of the copper was released from the wood during autoclaving, with copper citrate demonstrating the highest percent loss. Forty-four to 82 percent of the copper remaining in the samples following autoclaving was removed during exposure to the bacterium in liquid culture; copper naphthenate in oil and ACQ-D had losses of eighty percent or greater of the remaining copper. The bacterium removed as much or more total copper in 4 of 6 gas-sterilized samples (85-94%) than the cumulative effects of steam-sterilization and the bacterium on treated samples. Copper loss from in-service treated wood compromises the efficacy of copper-based wood preservatives.
D M Crawford, C A Clausen


Improved resistance of Scots pine and Spruce by application of an oil-heat treatment
2000 - IRG/WP 00-40162
Spruce (Picea abies L. Karst.) and Scots pine (Pinus sylvestris L.) were subject to a heat treatment which was carried out in an oil-bath. The aim was to improve the dimensional stability of the treated wood and its resistance against fungi. The bath of vegetable oil provides a uniform heat transfer at temperatures of 180°C, 200°C and 220°C and protects the submersed wood from oxygen. Heat treatment in air atmosphere was also carried out at the same temperatures for comparison. Wood treated in hot oil was more equal in its appearance than wood heated in hot air. The treatment of spruce and pine in the oil-bath resulted in a better resistance against Coniophora puteana in a lab test according to EN 113 compared to the treatment in air atmosphere. In order to achieve the wanted upgrading effect, certain changes of mechanical properties and colour must be accepted. However, the strength loss caused by the heat-treatment in oil was less severe than in air atmosphere. Since all materials and the energy used in the process originate from renewable resources, the oil-heat-treatment appears to be environmentally friendly. All in all, the heat treatment in oil might be a promising approach to upgrade wood for outdoor use.
M Sailer, A O Rapp, H Leithoff


Heat treatment of bamboo
2001 - IRG/WP 01-40216
Bamboo is a fast growing material with remarkable mechanical properties. In many tropical and subtropical countries bamboo is available in suitable dimensions for a reasonable price. Therefore it is used for many purposes which range from the basket production up to the industrial production of parquet or paper. However, bamboo is known as susceptible to fungal or insect attack and it is difficult to treat with preservatives. Therefore BFH investigated the possibility to protect bamboo by other methods and tested the application of a heat treatment. European grown bamboo (Phyllostachys viridiglaucescens) and Asian grown bamboo (Phyllostachys pubescens) were heat treated and were subsequently inoculated with the basidiomycetes Coniophora puteana, Coriolus versicolor and Schizophyllum commune in an agar block test. Further the durability of treated specimens against soft rot fungi was tested. The changes of the mechanical properties (MOE and shock resistance) caused by the heat treatment were determined too. The application of temperatures above 200°C caused a clearly enhanced durability against a basidiomycete as well as against a soft rot attack but the shock resistance was intensely reduced. Further investigations are still ongoing. The study has been carried out with financial support from the Commission of the European Communities, specific INCO programme INCO-DC 961344.
H Leithoff, R-D Peek


The effects of heat treament on the specific gravity of beech and spruce wood
2003 - IRG/WP 03-40254
The effects of heat treatment on specific gravity of beech (Fagus orientalis) and spruce wood (Picea orientalis) naturally grown and intensively used in forest products industry in Turkey were studied. The wood samples were cut into 2 x 2 x 3 cm. Heat treatment was than applied to the wood samples at four different temperatures (130 °C, 150 °C, 180 °C and 200 °C) and three different durations (2 h, 6 h and 10 h) under air atmospheres. The results indicated that the specific gravity values treated by heating generally exhibited a decrease with increasing the exposure durations and temperatures compared to the untreated wood samples.
S Yildiz, Ü C Yildiz, G Colakoglu, E D Gezer, A Temiz


The Effect of Heat on the Retention of Ammoniacal Copper Quat (ACQ-AB) onto Scots Pine (Pinus Sylvestris L.) Wood
2008 - IRG/WP 08-40390
In this study, the sapwood of Scots pine (Pinus sylvestris L.) were treated with ammonical copper quat type (ACQ-AB), which is one of the environmentally friendly wood preservatives, by using soaking method as a functions of various temperatures and time. The results indicated that the retention behaviour of ACQ onto the wood was considerably affected by temperature of ACQ solution and treatment time.
M Hakki Alma, A Mukremin Kara


Durability of different heat treated materials from industrial processes in ground contact
2005 - IRG/WP 05-40312
In this study the durability of heat treated wood originating from four different European industrial heat treatment processes in ground contact was examined. The manufacturers of heat treated material were: PLATO Hout B.V./Netherlands, Thermo Wood/Finland, New Option Wood/France and Menz Holz/Germany where Oil-Heat treated Wood (OHT) is produced. All heat treated materials showed significantly increased durability against decay in ground contact compared to untreated Scots pine (Pinus sylvestris L.), independent from the different heat treatment processes. After four years of field testing, heat treated material appears to be not suitable for in ground contact application, since long service life is required. In analogy to the classification of natural durability (EN 350-1, 1994), durability classes in the range from 2 (durable) to 4 (slightly durable) were achieved by the different heat treated materials. This stands in contrast to statements of suppliers, who promote their material as suitable for in ground applications.
C R Welzbacher, A O Rapp


The effects of heat treatment on the toughness of beech wood
2004 - IRG/WP 04-40283
The effects of heat treatment on toughness of beech (Fagus orientalis) wood naturally grown and intensively used in forest products industry in Turkey were studied. The wood samples were cut into 5 x 5 x 5 cm. Heat treatment was than applied to the wood samples at three different temperatures (130 °C, 150 °C and 180 °C) and three different durations (2 h, 6 h and 10 h) under air atmospheres. The results indicated that the toughness values treated by heating generally exhibited a decrease with increasing the exposure durations and temperatures compared to the untreated wood samples.
S Yildiz, Ü C Yildiz, E D Gezer, Ali Temiz, E Dizman


Effect of sterilization method on germination of spores of wood decay fungi observed by contact agar block method
1978 - IRG/WP 2117
Previous studies of germination of spores of wood decay fungi on wood have generally concluded that method of wood sterilization has little significant effect on germination response. This study expands the numbers of test fungi as well as number of sterilization methods employed to determine the influence of sterilization method on spore germination response of decay fungi. Germination was assessed on agar discs fused by aqueous diffusion path to 1 cm³ samples of aspen and white spruce sapwood.
E L Schmidt, D W French


The effects of heat treatment on anatomical changes of beech wood
2004 - IRG/WP 04-40284
The effects of heat treatment on anatomical changes of beech wood (Fagus orientalis) naturally grown and intensively used in forest products industry in Turkey were studied. The wood samples were cut into 2x2x3 cm and than conditioned at 25 °C and 65 % relative humidity for 3 weeks. Heat treatment was than applied to the wood samples at four different temperatures (130 °C, 150 °C, 180 °C and 200 °C) and three different durations (2 h and 10 h) under air atmospheres. The anatomical changes were determined for each heat treatment variation.
Ü C Yildiz, Z Gerçek, B Serdar, S Yildiz, E D Gezer, E Dizman, A Temiz


Heat treated timber in Finland
2000 - IRG/WP 00-40158
Heat treatment permanently changes the physical and chemical properties of wood by means of high temperatures (150 - 240°C). Heat treatment darkens the colour of the wood. Heat treatment improves the equilibrium moisture content of the wood and the shrinkage and swelling of the wood is reduced. Very high temperatures improve the resistance to rot and also reduce the susceptibility to fungal decay. At the same time the strength properties of the timber are reduced: the bending strength can fall by 30%, depending on the treatment conditions and the cleavage strength (tensile strength perpendicular to fibres) may be reduced to a half, which makes heat treated timber split easily. The improved characteristics of heat treated timber offer the timber product industry many potential and attractive new opportunities. Also wood species having no commercial value as such can be heat treated and in this way new uses can be found for these species.
T Syrjänen, E Kangas


Next Page