Your search resulted in 146 documents. Displaying 25 entries per page.
Comparative performance of wood/wood-based claddings predicted by four hygrothermal simulation tools
2019 - IRG/WP 19-20646
A number of hygrothermal numerical simulation packages are available, either wholly or partially dedicated to heat, air and moisture transfer simulations of building materials and wall assemblies. The objective of this work was to compare the hygrothermal responses and the moisture performance of western red cedar and composite wood claddings of a wood frame wall as predicted by four hygrothermal ...
M Defo, M Lacasse, A Laouadi
Field trial with poles of Scots pine treated with six different creosotes
1996 - IRG/WP 96-30115
In the middle of the 50's field trials with creosote-treated poles were started in France, Germany and Sweden. The trials were initiated by WEI (Western-European Institute for Wood Preservation). Six different creosotes were used and 40 poles per creosote were installed at each test field. Results after 39 years of exposure in Simlangsdalen, Sweden are reported. Poles treated with a heavy...
Ö Bergman
Screening potential preservatives against stain and mould fungi on pine timber in Zimbabwe
1995 - IRG/WP 95-30063
The search for environmentally and toxicologically safer chemicals for use in the timber preservative industry against stain and mould fungi has been intensified during the past few years. Results of field tests with two chemicals previously evaluated in the laboratory are presented. The conventional sodium pentachlorophenate was the more efficacious chemical against stain and mould fungi, providi...
A J Masuka
Observations on the colonization of freshly-felled timber treated with prophylactic chemicals by mould and sapstain fungi
1989 - IRG/WP 1394
Field tests using freshly felled pine sapwood were set up to determine the effectiveness of a range of antisapstain compounds and to study the problems of colonization by mould and sapstain fungi. Differences were recorded both in the overall performance of the compounds and also their selectivity in controlling specific fungal types. These results were found to be useful in gaining a better under...
G R Williams, D A Lewis
Proposed standard laboratory method for testing fungicides for controlling sapstain and mould on unseasoned lumber
1977 - IRG/WP 292
This laboratory method is for determining the effective concentration, or concentration for zero growth (CGo), for fungicides or preparations of fungicides which are potentially useful in protecting packaged or unseasoned lumber in storage and shipment from biodeterioration by sapstain fungi and moulds. The test is rapid and may be completed in three weeks and gives a good indication of the toxici...
A J Cserjesi
Preservative treatment of Eucalyptus saligna fence posts by the double-diffusion method
1982 - IRG/WP 3196
Eucalyptus saligna fence posts treated by the double-diffusion method with two chemical combinations showed average lives of 11.2 years (copper sulphate and potassium dichromate at 10.5 kg/m³ retention)and of 14.3 years (copper sulphate and sodium mono-H arsenate at 7.1 kg/m³ retention), as determined in five test sites in the State of Sao Paulo, Brazil. The exponential model was the best fit wh...
E S Lepage, A R De Freitas
Biological performance of gypsum products containing borates
2000 - IRG/WP 00-30237
At suitable retentions borates have biostatic properties enabling them to be used for biodeterioration control in wood. They provide protection against decay fungi, mould, and termites, which are known to also attack gypsum products. Currently, many gypsum products contain added borates, which are used to improve physical and processing characteristics. Work examining the effect of borates at cont...
J L Fogel, J D Lloyd
Mould resistance of lignocellulosic material treated with some protective chemicals
1984 - IRG/WP 3294
Effectiveness of preserving lignocellulosic material against moulding by treatement with water solutions of commercial wood preservatives and mixtures of various inorganic salts was investigated and compared with the effectivenes of sodium pentachlorophenoxide and boric acid....
K Lutomski
Influence of storage on mould susceptibility of wood at relative humidity values lower than 100%
1989 - IRG/WP 1413
It is well known that wood material changes with time because of different environmental influences. The effects of such changes on the subsequent mould susceptibility are less known. In this paper we report on increased mould susceptibility of pine wood after storage. Mould growth was detected by indirect methods....
J Bjurman
Moulds and indoor climate in Denmark
2003 - IRG/WP 03-10488
Just like in many other countries after the oil crisis in 1972 Danish houses were tightened with the result that the relative air humidity rose considerably. The Ministry of Energy also demanded a lowering of the indoor temperature from 25°C to 20°C with the result that the relative air humidity rose even more. According to the latest survey 10% of Danish buildings are infected with moulds. Moul...
J Bech-Andersen, S A Elborne
Effects of timber surface properties and dipping conditions on uptake of antisapstain actives from two aqueous suspensions, and ultimate effects on efficacy against mould and staining organisms
1995 - IRG/WP 95-30073
Green-off-saw rough sawn Pinus elliottii (slash pine) boards were dipped in aqueous suspensions of two antisapstain formulations, and the resultant surface retentions of active ingredients MTC (methylene bisthiocyanate), CTL (chlorothalonil) or TCMTB (2(thiocyanomethylthio)benzothiazole) were monitored by chemical analysis. Surface retentions increased with suspension concentration and surface rou...
M J Kennedy, T L Woods
Oxygen index levels and thermal analysis of wood treated with melamine-formaldehyde-boron combinations
1997 - IRG/WP 97-30135
Melamine formaldehyde (MF) resin was impregnated into scots pine (Pinus sylvestris L.) specimens with aqueous solutions of 5, 10 and 20% concs. Boric acid (BA) and borax (BX) was added to MF resin at the concentration levels of 0.25, 1.00 and 4.70% to each level of resin concs. BA and BX mixture was prepared at the 5:1 (w/w) ratio considering resultant pH of solutions and better fire resistance. U...
M K Yalinkilic, W-Y Su, Z Demirci, E Baysal, M Takahashi, S Ishihara
The effect of didecyldimethylammonium chloride on growth of different strains of mould fungus Gliocladium roseum
1995 - IRG/WP 95-10105
The tolerance and degrading ability of different strains of Gliocladium roseum towards didecyldimethylammonium chloride (DDAC) were studied. All four of the strains of Gliocladium roseum were tolerant to DDAC and after their growth on amended malt agar, the retention of DDAC in the medium was reduced....
Yu Zheng, J N R Ruddick
An evaluation of anti-apstain chemicals in Queensland, Australia
1986 - IRG/WP 3374
Five formulations were evaluated for potential use as antisapstain chemicals. Tolcide FSM (0.01, 0.02, 0.04%), Koppers N.P.-1 (0.70, 0.35, 0.25%), Kathon WT (0.10, 0.25, 0.40%) and Sinesto B (2.5, 5.0 and 7.5%) offer potential as antisapstain treatments. An incorrect stock of Busan 1009 was used resulting in unacceptable results....
L E Leightley
Evaluation of an alkyl ammonium compound as a fungicide to control sapstain and mould during diffusion storage
1984 - IRG/WP 3282
An alkyl ammonium compound ('Akzo' ES 255) was evaluated for its effectiveness against mould and sapstain during diffusion storage of boron-treated rubber wood. Though ES 255 at 1.0% concentration was effective against mould (71%) and sapstain (89%) it is less satisfactory compared to 0.5% sodium pentachlorophenoxide against mould (92%) and sapstain (98%)....
R Gnanaharan
Proposed degradation pathway for quaternary ammonium compounds by mould fungi
1996 - IRG/WP 96-10166
One group of chemicals that has attracted considerable attention as potential wood preservatives are the quaternary ammonium compounds (QACs). Based upon results of previous research this study confirmed the degradation pathway employed in QAC-tolerant fungi. For this experiment the two dialkylammonium compounds didecyldimethylammonnium chloride and dioctyldimethylammonium chloride were used. QAC-...
J L Bürgel, J Dubois, J N R Ruddick
A field test with anti-sapstain chemicals on sawn pine timber in Finland
1986 - IRG/WP 3368
Fourteen formulations, each in two concentrations, were tested for effectiveness against sapstain, mould and decay on Scots pine (Pinus sylvestris L.) in a field test in South-Finland. The trial was commenced in June 1985 and finished in October 1985. During the test the boards were infected mainly by mould fungi. In kiln dried boards the protective effects of nine and in green boards of four trea...
L Paajanen
Climate indices at work: Above ground decay L-joint tests (EN 330 and AWPA E9) at two sites 12000 km apart and with Scheffer climate indices of 60-65 and 300-330
1996 - IRG/WP 96-20095
Matched sets of Scots pine sapwood (Pinus sylvestris) L-joints were exposed above ground at two field sites for approximately five years. One site, at Garston, Watford, UK has a climate index between 60 and 65 while the other, close to Hilo, HI, USA has an index between 300 and 330. The joints were treated with a range of organic solvent treatments applied either by three minute dip immersion or b...
A F Preston, K J Archer, D M Roberts, J K Carey, A F Bravery
Growth of two selected sapstain fungi and one mould on chitosan amended nutrient medium
2003 - IRG/WP 03-10466
In vitro studies were undertaken to investigate the effect of chitosan on growth of Leptographium procerum, Sphaeropsis sapinea and Trichoderma harzianum. Chitosan was tested at three molecular weight (MW) ranges and different concentrations formulated as either a powdered suspension or as a solution.
The results generally showed that low MW chitosan produced a greater inhibitory effect on growt...
C Chittenden, R N Wakeling, B Kreber
The effective control of moulds on freshly impregnated wood
2004 - IRG/WP 04-30352
Beside natural timber it is known, that moulds can also groth at the surface of impregnated wood. This material shows “defects” like resistant dark spots or color changes and causes complaints. During the last years, the problem by moulds seems to increase.
Laboratory studies were carried out to show the effect of impregnations against moulds. Wood samples (Pinus sylvestris L.) were impregn...
G Cofta, K Lutomski, P Jüngel
Performance of treated spruce in Canadian field test sites
1989 - IRG/WP 3506
Spruce material under test in Canadian field test sites is performing better than anticipated. From the comparison of the performance of spruce treated with various preservatives, it appears that penetration may be far more important on durability performance than the preservative itself or the retention of preservatives in the wood. However, there is still insufficient data on the influence of pe...
J P Hösli, E E Doyle
Insect transmission of fungal sapstain to freshly sawn unseasoned softwood lumber
1994 - IRG/WP 94-20025
Chemical dip treatments were used to investigate micro-arthropod transmission of fungal sapstain to unseasoned pine sapwood boards. Saptain, mould and basidiomycete defacement of chemically treated sawn boards of Corsican pine was recorded during a 14 week field trial. Boards were treated with either a fungicide, an insecticide/acaricide, a combination of the fungicide with the insecticide/acarici...
M A Powell, R A Eaton, J F Webber
Thermotolerant mould growth in dehumidifier kilns in New Zealand
1996 - IRG/WP 96-10169
Growth of Aspergillus fumigatus and Paecilomyces variottii is common on wood dried in dehumidifier kilns that operate within a temperature range of 35-55°C. Aspergillus fumigatus causes an unacceptable blue / grey discolouration of the woods surface and prolonged exposure to spores during handling of mouldy wood can cause health problems amongst timber workers. A survey of dehumidifier kiln opera...
R N Wakeling, J G Van der Waals
In vitro studies on the effect of chitosan on mycelial growth and spore germination of decay fungi, moulds and staining fungi
2004 - IRG/WP 04-10507
The effect of solubilised, low molecular weight chitosan on established mycelial growth of a range of decay fungi, moulds and staining fungi was investigated using nutrient medium amended with different concentrations of chitosan that ranged from 0.1 to 0.4% weight per volume (%w/v). Also, spore germination of Trichoderma harzianum and Leptographium procerum was examined on chitosan amended nutrie...
C Chittenden, B Kreber, N McDowell, T Singh
Resistance of painted pine sapwood to mould fungi. Part 1. The effect of waterborne paints and fungicides on mould growth
1997 - IRG/WP 97-10233
The efficacy of different fungicides in acrylate and alkyd paints to protect pine sapwood against mould fungi was studied. The acrylate and alkyd paint systems with and without a preservative dipping treatment prior to painting were also used. Differences in the efficacy of the fungicides to protect the paint film were found. The paint films with isothiazolon and IBPC were resistant against mould ...
H Viitanen, P Ahola