Your search resulted in 3254 documents. Displaying 25 entries per page.
Evaluating the Effects of Post Dip-Treatment Laser Marking on Resistance to Feeding by Subterranean Termites
2016 - IRG/WP 16-10854
Dip-treatment of wood packing materials is often used instead of pressure treatment mainly because of issues relating to simplicity and cost. Packaging boxes fabricated for the United States Army are required to be dip-treated for at least one minute in an approved preservative solution prior to use. These boxes are expected to have a service life of up to 20 years in a wide variety of environment...
R A Arango, B Woodward, S Lebow
Release of Copper from Pressure Treated Wood
2016 - IRG/WP 16-20584
Micronized copper based wood preservatives including micronized copper quat (MCQ) and micronized copper azole (MCA) have been introduced commercially to the North American market since 2006 as alternatives to alkaline copper quat (ACQ) or soluble copper azole (CA) preservatives. Unlike ACQ or CA, MCQ and MCA use dispersed particulate copper particles rather than soluble ionic copper to make treat...
Jun Zhang, J Horton
Enhancing wood properties through bio-based and non-biocidal co-polyesters
2016 - IRG/WP 16-40740
The commonly used wood preservation treatments are nowadays facing huge environmental issues, as well as increasing public concern. As regards those concerns, legislation tends to regulate the use of biocidal preservation chemicals.
Thus, it does appear crucial to provide alternatives to the use of biocides to allow different outdoor uses of wood such as for, posts, decking, and cladding or even ...
C L’Hostis, M-F Thévenon, E Fredon, P Gérardin
Creosote leaching from timber bridges in Norway – a practical classification approach
2016 - IRG/WP 16-40744
Creosote is widely used as a wood preservative for highway timber bridges in Norway. However, excessive creosote leaching at various highway timber bridge sites leads to a bad reputation for the use of creosote treated timber constructions and the use of wood in general. Macro- and micro anatomical factors such as amount of heartwood, annual ring width, annual ring orientation, ray- height and com...
A Treu, K Zimmer
Development of a new method for wood hydrophobizing and fixation of copper compounds by chemical hardening of vegetable based modified oils
2016 - IRG/WP 16-40754
Wood products with ground and direct water contact, but without sufficient biological durability, have to be protected against biological degradation by fungi and other microorganisms. Due to European legislation (Biocidal Products Regulation 528/2012), the selection of possible chemical agents, which are still allowed to be used, is diminishing rapidly. The use of previously widely applied, very ...
C Swaboda, M Fischer, K Jacobs
Review of Leaching Experiments of CCA-Treated Wood and Wood Treated with Copper-based Alternatives
2017 - IRG/WP 17-50330
The objective of this study was to compare leaching rates of various wood preservatives from treated wood and the tests used to gather this information. The preservatives compared included CCA and the copper-based alternatives, MCQ, ACQ, and MCA. The tests compared included AWPA E11, SPLP, TCLP, and environmental leaching tests. Among all of the tests evaluated, environmental tests most closely si...
A Jones, J Marini, H Solo-Gabriele
Uncertainty in life cycle assessment of preservative treated wood – copper and freshwater ecotoxicity
2017 - IRG/WP 17-50331
Life cycle assessment (LCA) is a method for quantifying the environmental impacts of a product over the life cycle. In the last years, there have been a growing application of LCA in developments of environmental product declaration (EPD), which is utilised by professional procurement of materials for buildings. For legislative issues, LCA have also been used to assess application of creosote to t...
L G F Tellnes
Effects of wood protecting biofinish and linseed oil on fire behaviour and leachability of the fire retardant
2018 - IRG/WP 18-30728
A wood protecting biofinish is based on a protective and decorative fungal-based coating and a linseed oil impregnation (called Xyhlo biofinish). This biofinish enables the long-term use of wood in outdoor applications without using toxic chemicals.
The fire resistant properties of materials used in buildings are very important. Since Xyhlo biofinish is relatively new, only little information is ...
S Rensink, E J van Niewenhuijzen, M F Sailer
Selection of heat flux value for wood fire retardants testing using MLC
2018 - IRG/WP 18-40846
One of more crucial elements of investigating treated wood combustion properties with the use of a cone calorimeter is a proper selection of heat flux (HF). The HF level is directly reflected in time to ignition and a thermal degradation degree. The ignition of raw wood or of wood ineffectively protected against fire occurs at a low HF level, i.e. 10-20 kW/m2. By contrast, the ignition of wood whi...
B Mazela, W Perdoch, W Grześkowiak, A Batista
Influence of different triazoles as co-biocides in wood preservatives on efficacy and the environmental impact
2018 - IRG/WP 18-50333
In this study we investigated the efficacy and impact on the environment of different co-biocide triazoles in wood preservatives. Four different formulations (all containing 9.5% Copper) contained individual and combinations of cyproconazole, tebuconazole, propiconazole as co-biocides. Four formulations were tested according to EN 113 and EN 84 (ageing) to determine the brv for each formulation. T...
M Klamer, T Jensen, S Bang-Achton, E Morsing
Declaring life cycle inventory of toxicity related emissions in environmental product declarations of preservative treated wood products
2018 - IRG/WP 18-50339
Life cycle assessment (LCA) including impacts on toxicity for preservative treated wood has been shown to have large uncertainties. With the growing demand for verified LCA in environmental product declarations (EPD), the need for reliable data is crucial for realistic assessment of wood products. Uncertainty is caused by several issues such as service life prediction, leaching rates and calculati...
L G F Tellnes, C Askham, P-O Flæte, M Klamer
Improvement of wood decay and termite durability resulting from combined treatments based on borax/phenol-formaldehyde impregnation followed by thermal modification
2019 - IRG/WP 19-40871
This study determined the factors influencing the boron content after leaching of pine blocks impregnated with aqueous solution of phenol-formaldehyde (PF) resin with or without borax and subjected to heat treatment by response surface methodology. An experimental design permits to analyze the effects of heat treatment temperature (150, 185 and 220°C), curing time (5, 12, 5 and 20 hours), resin c...
S Salman, M-F Thevenon, A Petrissans, S Dumarcay, P Gerardin
A new approach to wood protection: Potential of biologically synthesised CuO and ZnO nanoparticle formulation as a wood preservative
2022 - IRG/WP 22-30758
Even though metal nanoparticles are effective in protecting wood, they are less preferred, as they are synthesised using methods which are expensive and are not environmentally friendly. Biological synthesis of nanoparticles using plants, fungi, yeast, bacteria and viruses, has been accepted as an alternative approach and is referred to as green synthesis. Utilization of biologically synthesised n...
Shiny K S, R Sundararaj, N Mamatha
Properties of Iron (II) Sulphate treated Norway Spruce
2022 - IRG/WP 22-30765
Exterior wood is exposed to various environmental factors that cause weathering. Weathering is important primarily from an aesthetic standpoint. However, not all parts of the building are equally susceptible to weathering. Parts exposed to moisture will discolour faster than protected parts, such as wood under roof overhangs. To achieve fast and uniform artificial greying, a surface treatment with...
B Lesar, M Humar, M Škamlec
Environmentally Friendly Wood Modification based on Tannin-Furfuryl alcohol - Effect on stabilisation, mechanical properties and decay durability
2022 - IRG/WP 22-40929
Furfurylation is a well-known wood modification technology. This paper studied the effect of tannin addition on the wood furfurylation. Three kinds of dicarboxylic acids, adipic acid, succinic acid, and tartaric acid, as well as glyoxal as a comparing agent, were used to catalyse the polymerisation of furanic or tannin-furanic solutions during wood modification. Impregnation of furanic or tannin-f...
M Mubarok, E Azadeh, F O Akong, S Dumarçay, A Pizzi, C Charbonnier-Gérardin, P Gérardin
Optimization of furfurylic alcohol/tannin ratio to improve the performance of biosourced thermoset resins for wood protection
2023 - IRG/WP 23-40994
This study concerns the chemical modification of wood with different ratios of tannin and furfuryl alcohol (FA) in the presence of maleic acid as catalyst. Tannins were used not only as cross-linking agents, but also as co-monomers to improve wood durability, while reducing the amount of FA used. Different aqueous formulations were prepared containing decreasing amount of FA (from 45.45% to 0%) an...
E Azadeh, A Pizzi, P Gérardin, C Gérardin-Charbonnier
Comparison of copper leaching from alkaline copper quat and copper compound nanosol-based wood preservative treated wood
2024 - IRG/WP 24-20726
To improve the leaching resistance of copper ion-based wood preservatives, copper compound nanosol-based wood preservatives were developed and its copper leaching characteristics were evaluated. Three types of preservatives (DC1, DC2, DC3) were prepared with different crystallinity and dispersant types of copper compound nanosol, and the copper concentration was adjusted to be the same as that of ...
Y-S Choi, S-M Yoon, J O Kim, J-G Kang, J-G Park
Leaching and chemical redistribution of CCA components in refractory heartwood of E. nitens
2024 - IRG/WP 24-41011
Chromated Copper Arsenate (CCA) is a wood preservative widely used to protect against fungal and insect attack. The fixation mechanism of CCA involves complex chemical reactions, including the reduction of chromium (VI) to chromium (III) and the formation of insoluble complexes. Despite fixation efforts, a portion of CCA components tends to leach from treated wood, influenced by factors like wood ...
J R Vargas, L Yermán, K C Wood, T Singh
Characterization of zinc borate synthesized in laboratory and scaled-up study
2025 - IRG/WP 25-20730
The organic nature of wood makes it vulnerable to both abiotic and biotic degradation. Impregnation with chemical products is a widely used method for wood protection. Inorganic borates exhibit a unique combination of properties that make them particularly effective for this purpose: they are insecticidal, fungicidal, and flame-retardant. In this study, ammoniacal zinc borate synthesized in labora...
Laffite, E Fernandez, C M Ibañez
Securing Flame Retardancy in Wood: Durability After Artificial and Natural Weathering Test
2025 - IRG/WP 25-20738
The outdoor use of wood is often limited by challenges such as dimensional instability, vulnerability to fungal decay, and high flammability. Traditional flame retardant treatments improve fire resistance but suffer from significant leaching under environmental exposure, reducing their long-term effectiveness. This study introduces an innovative solution by integrating flame retardants with DMDHEU...
M Wu, L Martin, H Militz
Curing Behaviour of Bio-based Phenol Formaldehyde Resin and the Durability Performance of Treated Wood
2025 - IRG/WP 25-20758
The aim of the study is to investigate the curing behaviours of bio-based PF resins treated Japanese Cedar (Cryptomeria japonica). Compared to conventional wood preservatives such as metal-based ACQ, bio-based PF resin was more environmentally-friendly and can store more plant-based carbon inside treated wood. However, all these preservatives have the risk of being leached out. This study conducte...
Y-S Lee, P-Y Kuo
Enhancing Wood Greying: A Study of Pre-Treatments and Iron(II) Sulphate Application
2025 - IRG/WP 25-41018
Recent trends in architecture and environmental policies have increased the demand for natural, unprotected wood in outdoor applications. However, wood exposed to the elements tends to grey unevenly, which can be problematic for visually important applications like timber façades. One solution is artificial greying with iron ions, providing a uniform colour that later transitions to natural greyi...
B Lesar, M Humar, A Kordiš
Danish wood preservatives approval system with special focus on assessment of the environmental risks associated with industrial wood preservatives
2001 - IRG/WP 01-50166-01
The following is a description of the procedure used by the Danish Environmental Protection Agency to assess the environmental risks associated with preservatives used in the pressure impregnation of wood. The risk assessment covers issues considered to be of significance for the environment and which are adequately documented so as to allow an assessment. Such issues are persistence and mobility ...
J Larsen
Data sheet on wood-boring insects. Apate monachus Fabricius. 2. Position systématique, nomenclature, identification et distribution - Espèces végétales attaquée
1981 - IRG/WP 1105
R L A Damoiseau
Confocal laser scanning microscopy of a novel decay in preservative treated radiata pine in wet acidic soils
1997 - IRG/WP 97-10215
Light microscopy of radiata pine (Pinus radiata D. Don) field test stakes (20x20x500mm3) exposed in wet acidic (pH 3-4) soil for 12 - 24 months showed predominance of an unusual type of decay characte-rised by tunnelling attack of wood cell walls. After two years decay was moderate to severe in wood treated to ground contact CCA specifications and also equivalent retentions of creosote, and a numb...
R N Wakeling, Ying Xiao, A P Singh