Your search resulted in 108 documents. Displaying 25 entries per page.
Experiences with supervision schemes for treated timber in Denmark
1984 - IRG/WP 3315
Since 1967 a voluntary supervision scheme for vacuum-pressure treatment was established in Denmark. In 1976 the Nordic Wood Preservation Council - NWPC - established a scheme based on wood preservation classes for treated timber as a joint technical standard valid in Denmark, Finland, Norway and Sweden. This paper deals with inspection results over 17 years for CCA treatment within our organizatio...
J Sabroe
Wood preservation in Brazil
1978 - IRG/WP 3126
Wood preservation was stablished in Brazil by 1902 in order to provide treated sleepers for railways, since there was a shortage of durable hardwoods in area served by railways. The growing need of sleepers and poles together with the availability of Eucalyptus spp. contributed for the development of wood preservation. Many wood preservation plants started to be stablished in 1957, and in 1977 the...
M S Cavalcante
A comparison of analytical techniques
1995 - IRG/WP 95-20061
This paper compares carefully-controlled weight retentions and analysis by XRF, ICP, combustion methods and a new extraction procedure for the new preservative, Copper(II) Dimethyldithiocarbamate (CDDC). Various experimental parameters such as particle size and drying conditions were investigated. In general, the correlations between and among the procedures are very high. The extraction-colorimet...
A C Gallacher, C R McIntyre, M H Freeman, D K Stokes, W B Smith
Wood preservation requirements in Queensland, Australia
1983 - IRG/WP 3227
In Queensland the preservative treatment and utilization of timber must comply with the Timber Users' Protection Act. Preservative retention levels and penetration patterns must be complied with. Analytical zones are specified for removing samples for chemical analysis of preservative retention. The required retention levels have been expressed as percent weight of oven dry wood weight. T...
L E Leightley, M J Kennedy
Issues Facing Wood Preservation in Australia Today
2003 - IRG/WP 03-30327
Timber and timber products are a major part of the Australian building industry and preservative treatment is a common consideration for most timber users. Despite this however, there is a major lack of awareness by the users of the various issues associated with preservative treatment.
Australian treatment specifications are logical, concise and uncomplicated. There are three agencies in Austr...
J Norton
Harmonisation of technical requirements of treated wood in Europe. What can we learn from the experience in the Nordic countries?
1995 - IRG/WP 95-50040-20
In the Nordic countries the Nordic Wood Preservation Council (NWPC) has since 1972 harmonised the technical requirements for pressure treated timber in a Nordic standard. These requirements were used by the control schemes that exist in every country. In 1976 the first Nordic standard for pressure treated wood was accepted and in 1978 NWPC changed from recommendations to approvals for the preserva...
F G Evans
Chemical analysis of wood waste - The problem of sampling
1999 - IRG/WP 99-20168
A quantitative analysis of the content of active substances in wood is often demanded in quality control after processing and for the proper waste management. As a measure for quality control, analysis has the advantage that the type of preservative is known and assumptions can be made about its distribution in the treated wood.W aste wood may have been treated by a wide range of organic and inorg...
A Peylo, R-D Peek
Non agricultural biocide directive. Practical proposals of implementation in the case where biocides are wood preservatives
1995 - IRG/WP 95-50040-24
This project of non-agricultural biocide directive has currently an extremely wide scope of pre-marketing authorization of substances and preparations used in numerous applications, other than agricultural. Elaborated on the 86/414/EEC model of the phytopharmaceutical product directive, the "NAB" draft directive aims to cover situations as different as plant or wood protection: in the case of plan...
G Ozanne
The use of low cost X-ray fluorescence instruments in the determination of copper chromium and arsenic in preservative treated wood
1987 - IRG/WP 2278
Internal quality control in timber treatment plants can be pursued by analysis of preservative treatment solutions and treated timber. Treaters must proceed with costly and lengthy analyses through analytical laboratories. An alternative approach for the timber treater, is to use low cost analysers (L.C.A.'s) based upon x-ray fluorescence. Detailed comparisons have been made between stand...
J Norton, L E Leightley
The study of blue stain found in coniferous timber in SR Slovenia (Yugoslavia)
1983 - IRG/WP 1177
The report concerns the problems connected with blue stain in coniferous timbers stored in warehouses at wood-processing plants in SR Slovenia (Yugoslavia). The amounts of spruce-wood (Picea abies Karst.) found to have been infected with blue stain have been measured and some of the fungi causing the stain have been identified and their biology studied. It was found that the percentage of spruce-w...
R Benko
Wood preservation in the Netherlands
1985 - IRG/WP 3324
This report gives some information on the production, import and use of timber in the Netherlands and, in more detail, about the country's wood preservation industry. As the country's production of wood that is useful for its manufacturing industries is very limited, the position of wood in the building industry is not too important. Architects think first in terms of bricks, con...
N Burgers, R Cockcroft, D De Jong
High-energy multiple impact (HEMI)-test – Part 1: A new tool for quality control of thermally modified timber
2006 - IRG/WP 06-20346
Thermal modification processes improve durability and dimensional stability of wood, but the strength properties, especially the dynamic ones, are compromised and need to be considered with respect to industrial quality control. Results from standard dynamic strength testing, such as impact bending tests, suffer from high variability, and therefore require a high number of replicates. To overcome ...
C Brischke, A O Rapp, C R Welzbacher
What is OECD doing to promote harmonization of biocide regulations
1999 - IRG/WP 99-20182
OECD began work on biocides in 1997 to help Member countries co-operate in the assessment and registration of these products. The work is a part of OECD's Pesticide Programme, and is co-ordinated by the Biocides Steering Group. The goal is to harmonize regulatory approaches to allow countries to conduct evaluations of biocides more efficiently. More efficient evaluations can advance the p...
M Paneli, N Grandy
Use of the Digital Refractometer for the On-site Analysis of Copper-based Preservative Systems
2007 - IRG/WP 07-20371
In some counties, there are no on-site chemical analysis methods available for treatment plants to use to determine the key active ingredients in the preservative treatment solutions. The complexity of the sophisticated methodology; cost of analytical instruments and training required for operating these instruments in treating plant level are the reasons for lacking such practice. In this paper...
L Jin, T Cashman, A Preston, J Trompetter, H Trompetter
Silver as a Wood Preservative Environmental Requirements and Concerns
2007 - IRG/WP 07-30420
The pesticide uses of silver and its compounds fall under the jurisdiction of the United States Environmental Protection Agency (USEPA) under the US Federal Insecticide Fungicide and Rodenticide Act. In addition, many other national and international organizations maintain close observance of the effects of silver in different environments. The US EPA has also issued a specific announcement that t...
J R Ellis
Run-off quality from sprinkled debarked logs and logs with bark from Picea abies and Pinus contorta
2007 - IRG/WP 07-50248
Storage of roundwood is necessary for efficient industrial production at sawmills and pulpmills. The need for wood storage becomes even more critical when large storm fellings create huge volumes of wood that is at risk for deterioration. In Scandinavia, the technique of sprinkling of water on roundwood is used to protect stored wood from fungal and insect infestation and drying during the summer....
M Jonsson
Quantitative and qualitative losses in wood of oriental spruce, Picea orientalis (L.) Link., induced by insects from forest to utility
2008 - IRG/WP 08-10647
In this study, some quantitative and qualitative losses in wood of oriental spruce, Picea orientalis (L.) Link., induced by insects from forest to utility were evaluated. In experimental plots, volume of trees damaged by Dendroctonus micans (Kug.) was 34% of the volume of total standing spruce trees in the oriental spruce forests of Turkey. The volume of standing trees that D. micans damaged was ...
H A Akinci, M Eroglu, G E Özcan, Ü C Yildiz
Influence of boiling on the quality of oakwood during peeling processes
2008 - IRG/WP 08-10656
Peeling process may be an efficient technology to transform secondary quality trees into veneer. After cutting and drying, veneer can be used for plywood or LVL production. If natural durability of these new panels is sufficient, they may be used for joinery production without preservative treatment. With the collaboration of ENSAM Cluny, Zvolen University and Pau University, we have investigated ...
M Svoradová, F Charrier, R Marchal, L Bléron, B Charrier, J-C Butaud
The susceptibility of hardwood plywood to white rot
2008 - IRG/WP 08-40397
The subject of the tests was resistance of veneer hardwood plywood to activity of pure culture of white rot fungus Trametes versicolor. The tested plywood was made with the use of the following glues: urea-formaldehyde (UF), melamine-urea-formaldehyde (MUF) or phenol-formaldehyde (FF). 4, 12 and 15 mm thick plywood was tested. External veneer of the plywood was mostly alder and the inner veneer (c...
A Fojutowski, A Kropacz
Chemical Analysis in Production Quality Control at Wood Treatment Plants
2008 - IRG/WP 08-20396
Analysis methods for quality control analysis in wood treatment plants have evolved with the changes in treatment preservative chemistries and analytical instrument technology. The basic hydrometer specific gravity measurements used for solution strength and classic wet chemistry methods for wood have given way to instrumental techniques such as X-ray fluorescence, automatic titrator, and HPLC. No...
P Walcheski, L Jin
Control de calidad eficiente de proteccion superficial sobre madera
2008 - IRG/WP 08-20397
Quality control is important to assure efficient protection of wood surfaces. When wood is exposed to the environment, it degrades due to weathering or environmental factors alone. Aging tests are utilized to test coating products. Quality control techniques are performed on exposed products according to standardized methods (NCh, ASTM, ISO, DIN, EN, FTMS, NTF, NBINT, or equivalents). Certified l...
A M Fernández S
The Present Situation and Future Development in Quality Assurance for Wood Protection in China
2009 - IRG/WP 09-20418
This paper provides a comprehensive review of the quality assurance program for wood protection industry in China in term of guiding policies, standardization and implementation activities. The potential deficiencies with the existing practices regarding to the quality of wood protection products and suggestions for the further research and development directions to improve the system are also dis...
Kang Hua Cheng
Biological Treatment to Improve Wood Product Quality and Durability - Fifteen Years of Effort and Experience at FPInnovations-Forintek Division
2009 - IRG/WP 09-40444
Wood plays an important role in the world economy. However, wood is subject to attack from wood-degrading fungi and insects and durability and quality of wood products are becoming increasing concerns for consumers. Development of effective and low environmental impact technologies to improve wood product quality and durability will be required to address these concerns. The application of a bio...
Dian-Qing Yang
Estimating the heat treatment intensity through various properties of thermally modified timber (TMT)
2009 - IRG/WP 09-40459
The suitability of different measures for prediction of the heat treatment intensity was investigated. Therefore, the resistance to impact milling (RIM), the lightness L*, the equilibrium moisture content (EMC), the anti swelling efficiency (ASE) and the total amount of soluble carbohydrates (TSC) of heat treated specimens were correlated with corresponding fungal resistance achieved by heat treat...
C R Welzbacher, C Brischke, A O Rapp
Morphological and Impregnability Properties of Narrow-Leaved Ash (Fraxinus angustifolia Vahl.) Wood Taken From Plantations with Different Spacings
2009 - IRG/WP 09-40475
Narrow-Leaved Ash, an important hardwood in Turkey, (Fraxinus angustifolia) is one of the fast growing species. In Turkey, several plantations have been established for 40 years. Narrow-Leaved Ash grows very fast and produces 25 (m3/year) mean increment. Except for eucalyptus and poplar, this increment is the highest compared to the other imported fast growing wood species. Until 1980, the spacing...
C Güler, H Ibrahim Sahin, S Sen