Your search resulted in 704 documents. Displaying 25 entries per page.
Update on lab and field test results for polymeric alkylphenol polysulfide treated wood
2002 - IRG/WP 02-40240
The possibility of using Polymeric Alkylphenol Polysulfide (PXTS) as a wood preservative has been undergoing evaluation in our laboratories for the past four years. Various formulations prepared from this compound have been tested and found to be effective against wood decay fungi and insects in field stakes after 42 months exposure. In accelerated soil bed tests, PXTS has been shown to be considerably more effective than creosote against both soft-rot and basidiomycete decay fungi. PXTS has also been shown to be effective against marine organisms and after 18 months exposure appears to have about the same efficacy as creosote. Preliminary treatment trials indicate that southern pine can be readily treated by the empty cell process
J Goswami, A Abramson, R Buff, D D Nicholas, T Schultz
Short term preconditioning of preservative-treated wood in soil contact in relation to performance in field trials
2000 - IRG/WP 00-20185
The effect of pre-exposure to primary colonising micro-organisms on preservative-treated wood, prior to a basidiomycete decay test, was determined by preconditioning in two soil types. Scots pine EN 113 blocks treated with 3 model systems (a triazole, a copper quaternary compound and a copper boron triazole) were leached according to EN 84 and subjected to 6 weeks and 8 weeks burial in either John Innes no. 2 (a loam-based horticultural compost) or soil from the Simlångsdalen field site in Sweden. The samples were then tested according to the method described in EN 113. Selective isolations were also performed after soil exposure and compared with those from a longer term field trial. Preconditioning lowered the effectiveness of the 2 copper containing preservatives. Some effect of soil pre-exposure could be noted with the triazole but this was limited. The fungal isolations from preconditioned EN 113 blocks and field exposed stakes were a similar mixture of soft rot and mould fungi. Bacteria were commonly isolated from the preconditioned wood. The role of these micro-organisms in the modification of the preservatives is currently being investigated.
S Molnar, D J Dickinson
An experimental method to simulate incipient decay of wood by basidiomycete fungi
2000 - IRG/WP 00-20200
At very early stages of decay of wood by basidiomycete fungi, strength loss can be measured from wood before any measurable weight loss. Therefore, strength loss is a more efficient measure of incipient decay than weight loss. However, common standard decay tests (e.g. EN 113 or ASTM D2017) use weight loss as the measure of decay. A method was developed that allowed progressive removal of samples so that all stages of colonisation and decay could be monitored by strength testing, weight loss determination and chemical analysis. Our results indicated that substantial and rapid decay (90% strength loss and 40% weight loss after 12 weeks) of southern pine by brown rot fungi was possible using the method. Our results also demonstrate a direct relationship between strength loss and weight loss and suggest a quantitative relationship between strength loss and chemical composition (hemicellulose sugars) during incipient decay of southern pine by basidiomycete fungi.
S F Curling, J E Winandy, C A Clausen
Co-operative research project on L-joint testing. Progress report to March 1984
1984 - IRG/WP 2211
Each participant was intended to expose L-joints in the main trial on 1 April 1983 and the first sampling, after 8 months exposure, was to be undertaken on 1 December 1983. Some participants have had to vary this schedule. Results are presented from CTFT (France) and PRL (United Kingdom). These show a greater effectiveness by the double vacuum treatments compared with the 1 minute dip treatments. However, results from the two locations differ particularly in the incidence and type of Basidiomycetes isolated.
J K Carey, A F Bravery
Co-operative research project on L-joint testing. Progress report to March 1986
1986 - IRG/WP 2272
Further sets of data received from CTFT (France) after 18 months exposure, BAM (Germany) after 18 months exposure, STU (Sweden) after 9.5 months exposure and TI (Denmark) after 12 and 17.5 months exposure are presented and discussed in conjunction with data previously reported. The new data are generally in agreement with those presented previously and indicate the major difference between the co-operating Institutes is one of the rate of colonisation rather than any relative difference in performance of the treatments. Overall 0.5% TnBTO 1 min dip treatment is providing least protection followed by 1.0% TnBTO 1 min dip. Both double vacuum treatments are providing better protection with little difference between 0.5% and 1.0% TnBTO.
J K Carey, A F Bravery
Co-operative research project on L-joint testing. Progress report to March 1985
1985 - IRG/WP 2236
It was originally intended that each participant would expose L-joints in the main trial on 1 April 1983 with the first sampling at 8 months (1 December 1983) and the second sampling at 18 months (1 October 1984). In the event, some participants have had to vary this schedule. Results after the first sampling have been received from CTFT (8 months), BAM (12 months) and Sipad-IRC (8 months) and after the second sampling from PRL (18 months) and Sipad-IRC (17 months). These, together with data presented previously, show a good correlation between gradual increases in permeability and the increasing incidence of Basidiomycetes. Both double vacuum treatments are proving more effective than the dip treatments; at the present stage 1.0% TnBTO appears to be no more effective than 0.5% TnBTO. The major difference between Institutes appears to be the rate at which colonisation and attack occurs rather than in the patterns of colonisation.
J K Carey, A F Bravery
Effects of the specimen position on fungal colonisation and wood decay by en 113 test fungi
1998 - IRG/WP 98-20136
For testing wood preservatives according to EN 113 it is common practice to plant the test blocks on neutral supports in order to prevent (1) a diffusion of chemicals into the agar medium and (2) an excessive moistening of the specimens. The procedure was employed in EN 350-1 for testing the natural durability of solid wood. It turned out to be of problematic nature because of the individual requirements of the test fungi. A certain degree of moisture can stop the virulence of one species, but - on the other hand - favour the virulence of another, so that different ratings of durability can be expected. In order to clarify this relation, blocks of durable and non-durable wood species were planted on different support materials and directly on the mycelial mat. Coniophora puteana, Coriolus versicolor, Gloeophyllum trabeum, and Poria placenta were used as test fungi. The results reveal a wide range with respect to the rate of colonisation and decay of the respective wood species if supports or no supports are used.
G Kleist, M-T Lenz, R-D Peek
Programme section 2, Test methodology and assessment
1997 - IRG/WP 97-20126
Progress report on co-operative research project on L-joint testing
1983 - IRG/WP 2192
A F Bravery, D J Dickinson, M Fougerousse
A comparison of soft rot, white rot and brown rot in CCA, CCP, CCF, CCB, TCMTB and benzalkonium chloride treated Pinus radiata IUFRO stakes, after 9-15 years exposure at five test sites in New Zealand
1991 - IRG/WP 1485
The aim of this study was to determine if decay type varies significantly between five field trial test sites of different soil type, aspect and climate in 9-15 year old, replicate CCA, CCF, CCP. CCB, TCMTB and AAC treated IUFRO stakes. A visual on-site assessment of decay type on every test stake was made and observations confirmed by microscopical examination. Regression analyses were used to determine significant differences of percentage frequency of occurrence of each rot type between sites and preservatives. Large differences in percentage frequency of occurrence of rot type were evident between sites. One site was dominated by brown rot (85%) and two were dominated by soft rot (99 and 91%). The fourth site had intermediate proportions of brown rot (40%) and soft rot (71%) but had the second highest occurrence of white rot (32%) (highest = 37%; lowest = 11%). The fifth site was distinct in that a large proportion of stakes (69%) had both well established brown rot and soft rot. Stakes at the other four sites tended to have only one rot type. Some highly significant preservative effects were also found. Possible causes of these differences are discussed in terms of inter-site soil type, climate and other differences.
R N Wakeling
Wood preservatives: Field tests out of ground contact. Brief survey of principles and methodology
1976 - IRG/WP 269
This paper contains the following spots: 1.: The general need for field tests. 2.: Interests and limits of field tests in ground contact. 3.: Various methods in use for out-of-ground contact field tests. 4.: Fungal cellar tests are they an alternative to above-ground decay exposure tests? 5.: Conclusions.
Collaborative soft rot tests. Names and addresses of collaborators
1973 - IRG/WP 231
A suggested method to test the toxicity of wood preservatives towards the house longhorn beetle
1977 - IRG/WP 275
This method was developed in the Institute for Wood Technology in Sarajevo, Yugoslavia and is used to get quick information on the toxicity of wood preservatives against house longhorn beetle (Hylotrupes bajulus). The method can be used for superficially treated or deeply impregnated wood blocks, and by using small or normal size test material it can be used as a laboratory or field test, and also for accelerated infestation of test material out of ground contact. The paper is given to the International Research Group on Wood Preservation as a suggested method which could possibly be used as a standard. Only the laboratory test method is described.
IRG/COIPM INTERNATIONAL MARINE TEST - to determine the effect of timber substrate on the effectiveness of water-borne salt preservatives in sea-water. Progress Report 2: Report of treatment and installation in Australia
1978 - IRG/WP 440
The purpose of this test and the procedures to be followed have been fully set out in documents distributed by the International Research Group on Wood Preservation and numbered IRG/WP/414 and IRG/WP/420. The prescriptions set out in these two documents have been closely followed.
Field test evaluation of preservatives and treatment methods for fence posts
1985 - IRG/WP 3347
This work presents the field test results after fifteen years exposure of Eucalyptus saligna fence posts treated with six different preservatives and five treatment methods. All the combinations with oil-borne preservatives presented the best results and among the waterborne preservatives, the fence posts treated by immersion method were with the lowest performance in the field test.
G A C Lopez, E S Lepage
A rapid field bioassay technique with subterranean termites
1983 - IRG/WP 1188
Details are summarised of a field procedure which is designed to ensure continuous exposure to a replenishing termite biomass. After pre-baiting to determine the presence and identification of a termite hazard, test specimens (35 x 35 x 250 mm³) are installed vertically in the ground adjacent to and in contact with bait specimens of the same dimensions and interconnected by susceptible feeder strip.
C D Howick, J W Creffield
Utilization of curcumin for detection of presence of boron in wood
1982 - IRG/WP 3191
It has been shown that curcumin is not a reliable reagent for detecting boron in wood that has been attacked by fungi
Performance of treated fence posts after 6 years in five test plots in the State of Sao Paulo - Brazil
1976 - IRG/WP 376
Fence posts treated with creosote, pentachlorophenol and creosote/ pentachlorophenol mixtures showed good performance after 6 years of exposure in five test plots located in the State of Sao Paulo - Brazil. Good results were also achieved with copper sulphate/sodium arsenate and copper sulphate/potassium dichromate mixtures. Fungi and termites were the main destroying agents found attacking the posts.
M S Cavalcante
How to Document the Performance of Super-Critical Treated Wood in above Ground Situations?
2005 - IRG/WP 05-20316
The paper presents practical experiences from the preparation of a new preservative treated wood product for introduction to the market. The product in question is Superwood™, which is treated with organic biocides using CO2 in a supercritical state as a solvent. The question is how to evaluate the performance of a new product such as Superwood™ in order to get an acceptance on the market and fulfil the formal requirements. In the European Union countries, the EN 599-1 is the standard that needs to be complied when approving a new product for the market, but it only focuses on the toxic limit against representative decay fungi according to EN 113. However, decay test, above ground and other forms of field tests are optional, this is not in line with the traditional test philosophy in the Scandinavian countries. The open question is to which extent treatment to the level of the toxic threshold value also ensures a long service life and expected performance of the treated commodity. Superwood™ is evaluated using a strategy, in which basic laboratory tests are done to get the toxic value (according to EN 599-1) and in addition a number of field tests are done including accelerated testing in the tropics. These tests are focussed on the evaluation of the performance criteria such as durability and service life and maintenance requirements. These questions must be answered by the producer without having a full record of performance test for their new products. A short status on the test performed on super-critical treated wood (Superwood™) is presented. Based on a comparison between field test in Scandinavia and in the tropical Malaysia a service life of more than 25 years for a specific supercritical treated product is estimated. It is stated that the existing European standardisation system is insufficient when it comes to service life prediction. A number of important questions need to be addressed by the European standardisation system as soon as possible because the market and the public opinion change quickly due to environmental concern.
N Morsing, A H H Wong, F Imsgard, O Henriksen
Influence of different fixation and ageing procedures on the leaching behaviour of copper from selected wood preservatives in laboratory trials
2003 - IRG/WP 03-20264
The paper focuses on the role of different parameters, such as fixation, sample size, wood species, and leaching in internationally standardized ageing procedures for wood preservatives from Europe, Japan and the United States. The leaching protocols used were EN 84, JIS K 1571 and AWPA E11 protocols. The wood species were Scots pine, Sugi and Southern Yellow Pine respectively. Three types of commercially important copper-based wood preservatives were used as model formulations, namely copper/copper-HDO, ammoniacal copper/quat and CCA. The most important factors determining the extent of copper leaching in the different lab trials were the sample size (volume/surface ratio) and the fixation conditions prior to leaching. On the other hand, the wood species and the leaching protocol itself were found to have only minor influence on the copper leaching rate in the test methods included in this study.
J Habicht, D Häntzschel, J Wittenzellner
Developments in the protection of wood and wood-based products
1980 - IRG/WP 340
Technology is playing an increasingly important role in the field of wood protection. This current review highlights how modern techniques have provided greater insight into the biological and physical processes affecting the durability of wood and wood-based products. Emphasis is also given to developments in preservative testing methodology and to the encouraging changes towards both the correct use of timber and the improvement of Standards and Codes of Practice. A final section, on recent technical developments in wood preservation, considers subjects ranging from an evaluation of new specific biocides to methods of increasing the permeability of refractory timber species.
J M Baker
IRG Working Group II. Co-operative leaching test (letter to collaborators)
1974 - IRG/WP 240
J W W Morgan
Testing of wood preservatives against marine borers (Part 1). Method of testing wood preservatives against marine borers (Part 2)
1971 - IRG/WP 37
P C Trussell, C C Walden
IRG/COIPM INTERNATIONAL MARINE TEST - to determine the effect of timber substrate on the effectiveness of water-borne salt preservatives in sea-water. 2nd Interim Report
1981 - IRG/WP 477
Three reference wood species - Alstonia scholaris, Fagus sylvatica and Pinus sylvestris, untreated and treated with 3%, 6% and 10% CCA and CCB solutions were supplied to all participants for submergence at local sites. Regular examination of samples is being carried out - 6 months, 12 months and then annually for 7 years.
R A Eaton
Co-operative research project on L-joint testing. Sampling after 8 months exposure
1983 - IRG/WP 2208
It was anticipated in Document No IRG/WP/2192 that exposure of L-joints by the European co-operators would take place on 1 April 1983. Where L-joints were exposed at this time, sampling after 8 months exposure is due on 1 December 1983. The present document draws attention to relevant previous documents which describe the sampling methods to be adopted. It also provides Tables for recording the results.
J K Carey, A F Bravery