IRG Documents Database and Compendium


Search and Download IRG Documents:



Between and , sort by


Displaying your search results

Your search resulted in 174 documents. Displaying 25 entries per page.


Quality of timber impregnated with preservatives of class AB after three years in service
2002 - IRG/WP 02-20241
Quality of impregnated timber is most often expressed by penetration and retention of the preservative used. Relatively less information is available about the performance of the final product, e.g. decks, panels etc. regarding product’s surface checks, deformations and overall appearance. Together with the timber durability, the above mention features are of esthetical importance in the above ground performance of timber. A comprehensive Nordic project dealing with pre-treatment, impregnation, durability and performance of Scots pine timber impregnated with copper-based preservatives for above ground use (class AB) was recently finished. The results from an above ground trail concerning the quality of timber are presented. The timber was dried in a conventional progressive, batch and high temperature kiln prior to impregnation. A significantly better quality regarding checks, deformations and deviation of the final moisture content, was achieved after conventional batch and high temperature dryings. Three preservatives (Kemwood ACQ 1900, Tanalith E and Wolmanit CX-8) were impregnated. The high temperature drying ensured the best penetration of all preservatives, but the retention was lower compared to conventional progressive and batch kiln dried timber. A part of the planks were conventionally kiln dried after the impregnation, the second part was air dried. Two decks with planks covering the variations in primary drying and preservative used were exposed; the former deck was in the open, the later one was under a shelter. After three years in service the planks were assessed regarding checks, deformations and moisture content. All three preservatives showed satisfactory appearance and no indication of decay was found. The deformations were comparable to those measured directly after final drying; the type of exposure had effect on the checks and moisture content of timber.
N Terziev


A field test with anti-sapstain chemicals on sawn pine timber stored and seasoned under different conditions
1984 - IRG/WP 3245
Newly sawn timber of European redwood (Pinus sylvestris L.) was dip treated in four different anti-sapstain chemicals. The protectife effect against sapstain, mould and decay was examined after 10 weeks' and 10 months' storage in open and closed stacks. The results showed that the performance of individual chemicals was different in open and close stacks, although the wood as well as the other storage and handling conditions were identical. This makes it possible explain some of the reported differences in performance of chemicals in different locations.
D J Dickinson, B Henningsson


Screening of modified linseed oils on their applicability in wood protection
2004 - IRG/WP 04-30346
In this study modified linseed oils, rape oil and three waxes were screened on their efficacy as wood protecting agents. By testing all products when impregnated with high retentions in Scots Pine sapwood on water repellence qualities, additionally an accelerated weathering test, drying quality, accelerated brown rot and blue stain test, an indication is formed of the capability of these products as wood protecting treatments. All oil and wax treatments significantly improve the water repellency of untreated wood. In weathering resistance, maleinised and polymerised linseed oil showed the best results in improving untreated pine sapwood dimensional stability thus reducing crack formation and decolourization by UV-light. In accelerated brown rot and blue stain tests boiled linseed oil significantly reduced degradation and staining. In addition, maleinised linseed oil and a mixture of modified linseed- and mineral oil are very well performing in the blue stain test. Overall most promising products are the maleinised oils and boiled linseed oil. The maleinised oils have good potentials in long lasting water repellency, showed some fungal growth prevention, are colour stable in weathering tests and create a dimensional stable wood product. Boiled linseed oil is not exceptionally good as a water repellent, but the good drying qualities together with easy handling makes this oil a promising product.
A Treu, J Lückers, H Militz


Evaluation effect of kiln schedule on Warp, Twist, Bow and surface checks in Poplar Wood
2011 - IRG/WP 11-40565
In this research, to establish a kiln-drying schedule for poplar (Populus nigra) lumber with 75 mm thickness that cut down from North Khorasan province in Iran, with three schedules T5-D2 (Forest Product Laboratory), T5-D3 and T8-D5 were adapted for drying the lumbers down to the final moisture content of 8±2%. primary dry bulb temperature each three schedules was adjusted at 49,49 and 54°C and the final dry bulb temperatures was adjusted at 71,60 and 82°C respectively. Quantity of defects including warp and surface checks of the lumber were measured before and after the drying process in each stage. In order to analysis the lumber defects for estimating the best schedule, quality control graphs were used. Results of investigation indicated that drying of poplar lumber by using of the three schedules was desired. However the first schedule (T5-D2) had better drying characteristics than the other schedules.
M. Akhtari, M.Arefkhani


Solvent drying and preservation of timber
1977 - IRG/WP 381
Processes which combine drying and preservation are first reviewed. Some preliminary experiments are then described in which blocks of green Sitka spruce sapwood were immersed, in a solution of tributyltin oxide (TBTO) in methanol at 60°C. Satisfactory penetration of the preservative and exchange of methanol and water occurred in a few hours. The methanol was removed rapidly from the wood by evaporation. Satisfactory penetration of TBTO into initially methanol-saturated samples occurred in a similar period. The factors influencing. such treatments are discussed. High initial moisture content of the wood and a high operating temperature are particularly desirable. Some aspects of the possible commercial operation of the process are discussed.
J A Petty


Low temperature drying conditions of Pinus radiata wood for avoiding internal stain
1989 - IRG/WP 3507
It has been observed that, if in little sawmills, timber is dried with a low temperature schedule, it arrives at destination with internal sapstain besides of superficial mould. In this study, the lowest drying temperature at which wood should be exposed for sterilization, which results to be 52°C, is searched. It is not possible to avoid entrainment of pentachlorophenol, even though a waiting period of 72 hours after dipping the wood in a pentachlorophenate/borax solution before drying is considered. The residual content of pentachlorophenol in wood should be at least 400 µg/cm² or the moisture content less than 23% for avoiding the development of mould.
M C Rose


Strength loss associated with steam conditioning and boron treatment of radiata pine framing
1987 - IRG/WP 3438
The combined effect of included defects and wood moisture content on the strength loss of second rotation radiata pine framing following conventional steam conditioning is investigated. The green Modulus of Elasticity (MOE) is reduced by approximately 13% after steaming. When dried after steaming, however, neither the MOE nor MOR is significantly different from unsteamed dried controls.
M J Collins, P Vinden


The use of pressure cycling to improve heartwood penetration in Pinus radiata (D. Don)
1995 - IRG/WP 95-40050
This study investigates the effect of cycling pressure on the treatability of radiata pine heartwood. The results indicate that liquid penetration into the heartwood is affected by the preconditioning method used and pressure treatment time. There is no significant improvement in the penetration of Pinus radiata (D. Don) heartwood when a cycling or pulsation process is used.
P R S Cobham, P Vinden


Spruce lumber treatments with ammoniacal solutions of inorganic preservatives
1977 - IRG/WP 391
As a part of our work in the Wood Preservation group at the Eastern Forest Products Laboratory in Ottawa to facilitate exploitation of spruce, which is a large timber resource in Canada, we have been studying the treatability of spruce roundwood. A report on this subject was presented to this group last year. More recently, another commodity - spruce timber - has been rapidly gaining the interest of wood treaters, mainly because of its potential use in permanent wooden foundations. We identified this trend and extended our research work to the treatability of spruce lumber.
R Rak


Borate thermal treatments
1992 - IRG/WP 92-3715
Green, partially seasoned (air-dried, steam conditioned), or kiln-dried southern pine timbers were treated thermally using 15% disodiumoctaborate tetrahydrate solution. After treatment, sections were stored under non-drying conditions to allow for diffusion. Results showed that effective treatment meeting the AWPA minimum retention (0.17 B203 pcf [2.72 kg/m³] in the outer inch) and penetration (2.5-in [64-mm] or 85% of the sapwood) could be obtained only with certain combinations of seasoning, treatment, and diffusion storage. The best results in terms of both retention and penetration were obtained with material steamed and stored prior to treatment using a 10-min hot bath time. Kiln-dried timbers could not be treated effectively. The results suggest that non-conforming treatment of green or partially seasoned timbers will require higher solution concentrations, higher hot bath temperatures, and/or longer diffusion periods to meet required standards. Results also indicated that treatment of smaller stock in dimension sizes (up to 2-in [50-mm]) should be feasible.
H M Barnes, R W Landers, L H Williams


A case study on quality control on telephone poles as a cost saving tool in Tanzania
1987 - IRG/WP 3418
A sample of 28 CCA treated Eucalyptus poles from a lot of 2,000 poles awaiting delivery to the field, was studied to reveal the quality of treatment. Results showed a product of very poor quality. Average figures for penetration and retention were 8.4 mm and 2.2 kg/m³; these results are 66% and 91% below the required standards, respectively. Consequences of such results are estimated to amount to losses of billion of shillings.
K K Murira


An investigation of the effects of pre-steaming on the treatment of sawn spruce timber with Celcure A, a copper-chrome-arsenic preservative
1981 - IRG/WP 3150
Difficulties in the treatment of spruce using standard vacuum/pressure techniques with both water-borne and organic solvent preservatives are well known. We have evaluated the influence of steaming on treatability with a waterborne CCA preservative.
C R Coggins


Radical changes in the requirements for more safe pressure impregnation in the Nordic countries in 1988
1990 - IRG/WP 3581
After introduction of quality control schemes and standards in the Nordic countries during the seventies, the first radical change of the standards and practice of work took place after pressure from the labor unions and authorities in 1988 and 1989 in Denmark and in Sweden. A new class of preservation with less retention for out of ground contact use was introduced, fixation times were prolonged to 6 and 14 days, and branding became a requirement. At the same time, treating companies replaced CCA with arsenic-free preservatives, and started using processes for accelerated fixation. Drying of treated wood was started to be used widely.
B Moldrup


Comparative investigations on the influence of wood seasoning, wood properties and temperature on the toxic values of wood preservatives against Hylotrupes egg larvae
1970 - IRG/WP 28
Comparative tests carried out at three institutes indicated the influence of kiln temperature, position of wood specimens in the cross sectional area and test temperature on the toxic values determined in accordance with DIN 52165 with egg larvae of the house longhorn beetle (Hylotrupes bajulus L.). The preservatives applied were boric acid in distilled water and g-benzene-hexachloride dissolved in chloroform; the timber species used was pine sapwood, (Pinus sylvestris L.). The method of seasoning had no influence on the toxic values of boric acid. With the g-BHC, however, the toxic values gradually increased with rising kiln temperatures (20°C, 70°C, 105°C). With boric acid the position of the sapwood samples in the log had no influence on the toxic efficacy; with g-BHC the efficacy was slightly greater in the outer sapwood, compared with the inner sapwood. The test temperatures (20°C, 24°C, 28°C) yielded different toxicity results for boric acid. At 24°C and 28°C the threshold values were somewhat below those of 20°C; they agreed with the values obtained at 20°C after a longer test period. With g-BHC different temperatures did not affect the results. An explanation is suggested for the causes of the influence exerted by the kiln temperature and wood properties on the toxic values of g-BHC. There was good agreement between the toxic values obtained in the different institutes.
G Becker, T Hof, O Wälchli


Observations on the failure of anti-sapstain treated timber under non-drying conditions
1990 - IRG/WP 1437
A range of bacteria and yeasts were isolated from antisapstain treated timber and fresh sawdust. Solution samples containing 100 ppm of TCMTB in a nutrient medium were inoculated with these organisms and incubated at 25°C for 5 days. The levels of TCMTB remaining in solution were determined by HPLC analysis after this time. Results indicated high losses of active ingredient for a range of organisms. These results suggest that active biodetoxification of organic biocides could occur in a short period of time during storage of antisapstain treated timber under favourable conditions. The implications of these results are discussed.
G R Williams


Accelerated fixation of CCA in borak bamboo (Bambusa balcooa Roxb.) of Bangladesh
2001 - IRG/WP 01-40193
CCA-C fixation study on impregnated (6% CCA solution), then boiled, oven-dried, normal, air-dried and steamed bamboo slices of air-dried borak bamboo (Bambusa balocca Roxb) of Bangladesh, revealed almost complete fixation in steamed (accelerated fixation) and air-dried (3 weeks, slow fixation) bamboo slices compared to moderate to slow fixation in boiled, oven-dried, normal and 24h air-dried slices.
A K Lahiry


Wood preservation in France. "Bois plus" chain of quality. Description of the scheme early 1989
1989 - IRG/WP 3519
1989 - description of the French "CTB-BOIS PLUS" homologation scheme...
G Ozanne


Wood Preservation in France. A statement of quality control early 1986
1986 - IRG/WP 3389
A statement of quality control in France early 1986 - Summary of new - Standards criteria for preservatives and treated wood - Aptitude of treated wood for use per class of biological hazard
M Romeis, G Ozanne


A simple leaching procedure for in-plant monitoring of CCA fixation
1993 - IRG/WP 93-30023
A simple leaching test is described to quantitatively estimate the extent of fixation of chromated copper arsenate (CCA) preservative treated wood products. It is based on the reaction between diphenylcarbazide and unreacted hexavalent chromium leached from borings taken from treated wood during the fixation process. The test requires about 20 minutes to complete and can be set up in a treating plant quality control laboratory for less than US $1000.00.
P A Cooper, Y T Ung


Steam conditioning of partially dried radiata and Corsican pine roundwood
1988 - IRG/WP 3499
The effect of partial air drying prior to steam conditioning and its effect on subsequent preservative treatment by the Bethell treatment process was investigated. A high standard of preservative treatment was obtained in both radiata and Corsican pine, irrespective of whether a period of partial drying was imposed before or after steam conditioning.
P Vinden, D R Page, K Nasheri


Water-repellent additive for CCA
1991 - IRG/WP 3655
Hickson have developed a water repellent additive for incorporation into copper-chromium-arsenate timber treatment solutions. The water repellent emulsion shows good stability in the treatment solution, is easily incorporated and applied in a single stage treatment. No modifications to the additive is safe to treatment schedule are usually needed and use. Weathering of the treated wood is substantially inhibited by the presence of the additive. Adhesion of paints is not affected.
P Warburton, R F Fox, J A Cornfield


Survey of conditioning treatment practices in India
1978 - IRG/WP 3127
India has 75.3 million hectares (ie about 24% of total land area) under forests out of which the area of productive forests, from which industrial wood is available, is about 60 million ha. The Task Force on Forest Resources Survey has tentatively estimated that the total growing stock in Indian Forests is 24,000 million cubic metres (m³). The total recorded production of wood in the country is roughly estimated as 25 million m³ annually of which approximately 10 million m³ is demanded by various industries and the remaining is used as fuel. India, with developing economy needs very large resources of timbers for diverse purposes. There is already shortage of timber in the country for various wood based industries and it is expected this will progressively increase with the rapid pace of industrialisation. However, suitable measures are being taken to bridge the gap between demand and supply. The entire 10 m³ of industrial wood requires some sort of protection against wood-destroying agencies. Timber awaiting conversion during storage needs prophylactic treatment while for use as poles, fence posts, sleepers, building material, in cooling towers, boats, ships, in mines, in sea-water, etc., timber should be adequately treated with suitable wood preservatives to obtain satisfactory service life. Both heart and sapwood of non-durable species and only sapwood of durable species need protection against wood-destroying agencies. Wood Preservation on scientific and modern lines was introduced in India by Sir Ralph Pearson of the Indian Forest Service in the year 1908. In India, the first wood preservation plant was established at Bally in Howrah in 1854. Of the total timber extracted in India, only a very small proportion, estimated at about 5% is treated. This amounts to 0.45-0.50 million m³ of wood per annum. The total annual capacity of 140 preservation units, existing in the country at present, is estimated at 0.43 million m³ on single shift basis. IS: 401-1967 (Indian Standard - Code of Practice for Preservation of Timber) covers types of preservatives, their brief descriptions, methods of treatment, and the type and choice of treatment for different species of timber for a number of uses. This standard includes only such preservatives and methods of treatment which have given satisfactory results under Indian condition of service. According to this standard, whatever process of treatment is adopted, timber for treatment should be sound and should be dried to an appropriate moisture content (generally not more than 15% for open tank and 25% for pressure processes). All the wood working etc should be done prior to treatment. In case of timbers, specially some conifers having non-durable heartwood which is refractory to treatment, when treating thick members like railway sleepers, beams, piles, etc, incision of all the surfaces, other than the ends, to a depth of 12-20 mm is necessary.
M C Tewari


Treatment of dried sawn spruce and redwood building timbers with water-borne preservatives under a scheme for the quality control of the preservation and preserved wood in the Netherlands
1978 - IRG/WP 3123
Treatment of dried sawn spruce and redwood Building Timbers with water-borne preservatives under a scheme for the quality control of the preservation and preserved wood in the Netherlands. The aim of this article is to give the reader a modest description of the evaluation of fundamental research in wood preservation into a practical application.
H F M Nijman, N Burgers


Analysing the characteristic role of moisture content for drying and fluid flow in Sitka spruce. - Part 1: The drying process of sapwood and heartwood of two different thickness of Sitka spruce using a kiln. - Part 2: Effects of moisture content on longitudinal permeability of Sitka spruce in vertical variation of the tree
2000 - IRG/WP 00-40173
The characteristic role of the moisture content in Sitka spruce (Picea sitchensis (Bong.) Carr.) that grown in the United Kingdom was examined by this study on the basis of (1) the reduction of moisture content in two different thickness of sapwood and heartwood by kiln drying process, and (2) the effects of moisture content to the longitudinal void volume filled of tanalith-C by the full-cell process from base (1 m) to apex (3 m) of the tree in sapwood zone. Accordingly, conclusions on indication of the drying process of sapwood and heartwood, and vertical variation of longitudinal flow with effects of moisture were listed separately: (1) Comparison of Drying Characteristic of Sapwood and Heartwood: The two different thickness (300x30x30 mm3 and 300x20x20 mm3) of sapwood and heartwood of Sitka spruce was dried using the suggested drying schedule in kiln. The reduction of moisture was schematically diagrammed according to sapwood and heartwood stakes. The reduction of moisture followed the same downward trend that sapwood (S) loses more moisture than heartwood (H) although the small stakes of S and H lost moisture rapidly compared with the large ones. (2) Vertical Variation of Moisture Content and Longitudinal Permeability: The 90 kiln dried defect free sapwood stakes (150x25x25 mm3) of Sitka spruce was taken from base to apex of the trees at 1, 2 and 3 m above ground level. After having the determination of moisture content in each experimental stake, the treatment was carried out by the full-cell process with CCA preservative (Tanalith-C) using a model pressure treatment plant. Significant differences observed among the tree heights from 1 to 3 m showing that slightly increases of moisture content from base to apex and conversely decreases of longitudinal void volume filled by preservative fluid.
I Usta


Preservative treatment of Pinus elliottii
1987 - IRG/WP 3435
The treatment of Pinus elliottii with copper-chrome-arsenic preservative by four alternative seasoning and treatment methods is investigated. Steam conditioning followed by either alternating pressure method (APM) or 'Q' treatment resulted in inadequate preservative penetration. Air drying or high temperature drying followed by the Bethell process resulted in a high standard of treatment.
P Vinden, L Carter


Next Page