Your search resulted in 3797 documents. Displaying 25 entries per page.
Above and Below-Ground Depletion of Copper, Chromium and Arsenic from Pinus radiata and Fagus sylvatica at Thirteen Test Sites in New Zealand and Australia
2006 - IRG/WP 06-30402
The objective was to determine the significance of site and wood species on preservative depletion for a copper chrome arsenate preservative (CCA) from 20 x 20 x 500 mm field test stakes after 5.5 and 4.5 years for pine and beech respectively. At least 5 sacrificial stakes were used to produce site means. Site and wood species had a major effect on copper, chromium and arsenic loss from CCA treate...
R Wakeling
Addition of boron compounds and octanoic acid for improvement of biocidal properties and copper fixation at copper-ethanolamine based wood preservatives
2006 - IRG/WP 06-30408
Copper-ethanolamine based wood preservatives became important active substance (formulation) for wood protection, novelty. As copper itself can not ensure sufficient protection against wood destroying organisms and fixation in wood we combine it with other biocides like ethanolamine, boron and octanoic acid. This investigates were performance on spruce wood impregnated with different combination o...
F Pohleven, M Humar
Long term marine performance of ACZA treated Hem fir in Krishnapatnam harbour, east coast of India
2006 - IRG/WP 06-30409
The performance of Hem fir (Tsuga heterophylla) and Southern pine (Pinus sp.) treated with ammoniacal copper zinc arsenate (ACZA) and copper dimethyldithio carbamate (CDDC) at two retention levels of each preservative was assessed in tropical marine waters at Krishnapatnam harbour on the east coast of India. Panels treated with ACZA of lower loadings (23.1 Kg/m3) had failed in 38 months while the ...
B Tarakanadha, K S Rao, J J Morrell
Copper borate for the protection of engineered wood products
2006 - IRG/WP 06-40334
Copper borate was evaluated for use in protecting oriented strand board (OSB) from mould, decay, and termites. Aspen OSB bonded with either phenolic or isocyanate resin was treated with several formulations of copper borate at various loadings from 0.26 to 4 percent by weight. These panels were then tested to determine the impact of the preservative on mechanical properties as well as resistance ...
R Smart, W Wall
CCB Preservative treatment of split muli (Melocanna baccifera ) bamboo by soaking process
2006 - IRG/WP 06-40336
This study was carried out in order to investigate the retention of chemicals inside the split muli ( Melocanna baccifera ) bamboo after preservative treatment by soaking process. Treatment with 10% aqueous solution of CCB (copper-chrome-boron) was applied in split bamboo of two sizes (1/4 part and 1/8 part) at three different moisture contents and five time periods (24, 48, 72, 96, 120 hours). It...
K Akhter, M H Chowdhury
Characteristics of treated oriented strand lumber using recycle chips
2006 - IRG/WP 06-40343
The Kyoto Protocol for preventing global warming has come into effect, and the Cabinet Council was decided on the amount of carbon dioxide exhaust to be reduced in Japan. Moreover, the recycling of demolition waste wood is mandated under the “Construction Material Recycling Law” as one of the mechanisms for Japan to form the recycling society. The law encourages the utilization of demolition w...
T Shibusawa, A Miyatake, K Yamamoto, K Hashimoto, H Sonobe
Non-pressure preservation technique of five less durable timber species – Kadam (Anthocephalus cadamba), Shimul (Bombax ceiba), Pithalu (Trewia nudiflora), Am (Mangifera indica) and Boroi (Ziziphus jujube) of Bangladesh
2006 - IRG/WP 06-40322
Wood is a versatile renewable resource, which has been extensively used as a reliable construction material as well in furniture ever since the beginning of civilization.
The Major disadvantage of wood is its susceptibility to biodeterioration by fungi, insects and bacteria. In tropical countries like Bangladesh, fungi is the most significant of these biodeterioration agents. Kadam (Anthocephalus...
G N M Ilias, A H Kabir, F Begum, M F Alam
Corrosiveness of metal by copper-based preservatives
2006 - IRG/WP 06-40329
The corrosive rates of 4 types of metal as well as epoxy-coated metal by a variety of preservatives derived from different copper source and ingredients were conducted in this paper. The main results shown that: CCA is less corrosive to red brass and Q235A steel than other copper formulations; Copper-based preservatives such as ACQ and copper azole derived from basic cupric carbonate or cupric hyd...
Ying Zhang, Mingliang Jiang
Assessment of the ease of preservative treatment in the less-valuable Nigerian-grown Ceiba pentandra wood
2006 - IRG/WP 06-40330
The hardwood Ceiba pentandra locally known as “araba“ in Nigeria is rarely used for structural and construction works due to its high dimensional instability, low strength and durability values. Samples (25 x 50 x 600mm) were removed from four green boards (25 x 200 x 3000mm) of this species originating from a natural forest stand in Nigeria. The sapwood and heartwood were differentiated by me...
L Awoyemi, A J Pitman
Resistance of DMDHEU-treated pine wood against termite and fungi attack in field testing according to EN 252. Results after 30 months
2006 - IRG/WP 06-40354
The aim of this study was to determine the effectiveness against decay and termite attack of pine sapwood treated with pure and modified DMDHEU in a field test according to European Standard EN 252. Some of the treatments tested were able to increase, within the period of the test reported (30 months), the resistance of the wood both to micro-organisms and termites. The curing process seems to be ...
S Schaffert, L Nunes, A Krause, H Militz
Thermal decomposition behavior of CCA-treated wood for safe disposal and the safe recovery of heavy metals through pyrolysis
2006 - IRG/WP 06-50238
If we could estimate the chemical changes in heavy metals by temperature in chromated copper arsenate (CCA)-treated wood during pyrolysis, it is expected that we could solve the environmental problems of heavy metals, which may occur during pyrolysis, and therefore, the thermal decomposition behavior of effective elements of CCA-treated wood was examined to find a safe disposal method. First, CCA-...
Dong Won Son, Dong-heub Lee, Sun-hae Cheon, Myung Jae Lee
A Prediction of Arsenic Groundwater Concentrations Influenced by Construction and Demolition Debris Landfills in Florida Containing CCA-Treated Wood
2006 - IRG/WP 06-50242
Groundwater fate and transport models can provide an indication of the potential impacts of arsenic from the infiltration of leachate from unlined C&D debris landfills containing CCA-treated wood. A solute transport model, Migration of Organic/Inorganic Chemicals (MYGRT), was chosen to predict groundwater contaminant concentrations at specified locations from a hypothetical source (C&D lan...
J Jambeck, T Townsend, H Solo-Gabriele
Detecting fungal DNA in treated and non-treated wood
2007 - IRG/WP 07-10621
Isolating fungi from wood has long involved culturing on selective media followed by identification using various keys. This process can be cumbersome, costly, and, most importantly, not always capable of detecting all of the fungi present. The recent development of molecular methods for isolation and identification of fungi has created tremendous opportunities for expanding our knowledge of the...
C Freitag, M Freitag, J Morrell
Assaying Pentachlorophenol-treated Wood Using XRF
2007 - IRG/WP 07-20362
A study was conducted to evaluate the effect of oil type on the performance of test posts treated with oil-penta and exposed in DeQueen, AR for forty years in ground contact. The original assays for the poles were done by lime ignition, a practice used sparingly today in treating plants or by independent inspectors, in part due to the complicated analysis procedure and chances for error. XRF ins...
H M Barnes, C R McIntyre, D W Bullock , M H Freeman, G B Lindsey
Quantitative Determination of Cyproconazole in Wood treated with Tanalith CY
2007 - IRG/WP 07-20369
The HPLC method has been widely applied to quantitative determination of cyproconazole in preservative solutions. However, HPLC assay has not been successfully employed to determine cyproconazole content in treated wood. Some extractives from treated wood hinder cyproconazole determination because they have a similar retention time to that of cyproconazole on an HPLC chromatogram. In addition, ...
I Momohara, T Miyauchi, M Mori
Use of the Digital Refractometer for the On-site Analysis of Copper-based Preservative Systems
2007 - IRG/WP 07-20371
In some counties, there are no on-site chemical analysis methods available for treatment plants to use to determine the key active ingredients in the preservative treatment solutions. The complexity of the sophisticated methodology; cost of analytical instruments and training required for operating these instruments in treating plant level are the reasons for lacking such practice. In this paper...
L Jin, T Cashman, A Preston, J Trompetter, H Trompetter
Permethrin: A Critical Review of an Effective Wood Preservative Insecticide
2007 - IRG/WP 07-30413
Permethrin is a synthetic pyrethroid used in the wood preservation industry. The generally favorable environmental profile of pyrethroids coupled with their high efficacy led to their wide substitution of the chemically resistant organochlorines dieldrin, lindane, and chlordane formerly used for protection of buildings against wood destroying organisms. Much of the research on performance of perm...
M H Freeman, D N Obanda, T F Shupe
Efficacy of chitosan in combination with GRAS (Generally Recognised As Safe) compounds as a potential wood preservative
2007 - IRG/WP 07-30414
In vitro studies were undertaken to evaluate the synergy between chitosan and selected GRAS (Generally Recognised As Safe) compounds against two sapstain fungi Sphaeropsis sapinea and Leptographium procerum. Bioassays performed on nutrient medium suggested that some of the GRAS compounds tested including sodium benzoate, potassium sorbate and ascorbic acid had a synergistic effect when combined w...
C Chittenden, K Thämelt, T Singh
Silver – The Next Generation Wood Preservative
2007 - IRG/WP 07-30419
The successful introduction and commercial use of products designed to have controlled release of silver ion over long time periods prompted the Silver Research Consortium and the US Forest Products Laboratory to undertake research to see if silver could also be an effective wood preservative to be used in place of chromated copper arsenate (CCA) now prohibited for use in the United States and els...
J R Ellis, K Jayachandran, D Nicholas
Silver as a Wood Preservative Environmental Requirements and Concerns
2007 - IRG/WP 07-30420
The pesticide uses of silver and its compounds fall under the jurisdiction of the United States Environmental Protection Agency (USEPA) under the US Federal Insecticide Fungicide and Rodenticide Act. In addition, many other national and international organizations maintain close observance of the effects of silver in different environments. The US EPA has also issued a specific announcement that t...
J R Ellis
Preservative treatment of Golla cane (Daemonorops jenkinsiana) by pressure process
2007 - IRG/WP 07-40379
The feasibility of preservative treatment of golla cane (Daemonorops jenkinsiana (Griff) Mart). by pressure process has been studied using water borne preservatives CCB (copper-chrome-boron). Cane samples of three different lengths 1m, 2m and 3 m. were treated at different pressure and time period to evaluate the extent of penetration and retention of preservative chemicals. It was observed that t...
K Akhter, M Hoque Chowdhury
Copper fixation in ACQ-D treated Chinese fir at various temperature and relative humidity conditions
2007 - IRG/WP 07-30436
In this study, the effect of different conditions of temperature, relative humidity, and duration of post-treatments on accelerating copper fixation in ACQ-D treated Chinese fir wood blocks was investigated. The conditions include the combination of three temperatures (21, 50, and 70?) and two relative humidity levels (20% and 80%), also include four temperatures (50, 70, 90, and 110?) without con...
Jinzhen Cao, Lili Yu
Natural Weathering of Coated Oil Heat Treated Wood
2007 - IRG/WP 07-30440
Oil heat-treated (thermally modified) pine wood was coated with 9 different types of solvent- or water-borne exterior finishes. The systems with modified wood substrate as well as unpainted and painted non-modified controls were exposed to weathering (EN 927-3) on two locations with sub-alpine and alpine climate. The influence of natural ageing on surface systems was evaluated after one year of ex...
M Petric, B Kricej, M Pavlic, A Rapp
Mold resistance of heat-treated wood
2007 - IRG/WP 07-40358
The resistance of heat-treated sugi sapwood against three mold fungi was evaluated. Wood specimens were first subjected to heat treatments at 180 and 220ºC for 2 and 4 hours. Mold growth on the surface of the specimens was measured 1, 2, 4 and 6 weeks after the inoculation with the fungi in laboratory conditions. Laboratory decay tests were performed using two brown and white-rot fungi along with...
S N Kartal
Fire, flame resistance and thermal properties of oil thermally-treated wood
2007 - IRG/WP 07-40361
Oil thermal treatment, first developed by German scientists, is a promising technology for improving the durability and dimensional stability of wood for outdoor above-ground residential uses such as siding and shingles. The present authors’ previous research showed that 220ºC is an optimal treatment temperature, with 2 hours’ treatment producing wood with significantly improved moisture and ...
Jieying Wang, P Cooper