Your search resulted in 167 documents. Displaying 25 entries per page.
Heat transfer and wood moisture effects in moderate temperature fixation of CCA treated wood
1994 - IRG/WP 94-40022
Practical aspects of heat transfer and fixation of wood exposed to drying conditions after CCA treatment are considered. The rates of heat transfer and CCA fixation are substantially influenced by the cooling effect of water evaporating from the wood surface when drying occurs during fixation. At least in the early stages of fixation, the wood temperature approaches the wet bulb temperature, rathe...
J Chen, M Kaldas, Y T Ung, P A Cooper
Status of wood preservation industry in India
2005 - IRG/WP 05-30388
The paper traces the history of wood preservation industry in India, listing various mile stones for creation of treating capacity. The preservation industry developed with the development of rail road system on the line of most other developed countries. The most popular wood preservatives are CCA, CCB, ACC, Creosote and recently LOSP have also appeared in the market. The major users of CCA is th...
S Kumar
Controlling marine borer attack of timber piles with plastic wraps
1981 - IRG/WP 479
Plastic films 20 to 40 mils thick have been used for many years to wrap creosoted timber piles in service to protect them from attack by marine borers. As long as the wrap remains undamaged, this procedure provides complete protection to the pile. Properly applied, wraps generally provide protection for 25 yeara or longer. Polyvinyl chloride (PVC) and polyethylene (PE) films are specially formulat...
F Steiger, G Horeczko
Fundamentals on steam fixation of chromated wood preservatives
1988 - IRG/WP 3483
Weathering of treated wood directly after impregnation leaches up to 2% of copper-chromate-containing wood preservatives. Almost total fixation of Cr+6 is achieved by steaming the treated wood at 100°C to 120°C, preferably 110°C. To initiate such spontaneous fixation 85°C to 90°C inside the wood are essential, which requires heating times ranging from 20 to 80 min, depending on timber species...
R-D Peek, H Willeitner
Investigation of the suitability of silver fir (Abies alba Mill.) for thermal modification
2004 - IRG/WP 04-40275
In this study the suitability of silver fir (Abies alba Mill.) was examined for thermal modification. Comparative experimental investigations were performed with silver fir and Norway spruce (Picea abies Karst.) after thermal treatments. Besides properties, which characterize the quality of heat treatments, like dimensional stability and resistance against fungal attack, strength properties of the...
C Brischke, A O Rapp
Durability aspects of (hydro)thermal treated wood
2000 - IRG/WP 00-40160
Samples of several wood species were treated in a two steps process, subsequently hydrothermal and dry heat-treated, by the so-called PLATO-process and analysed for their resistance against fungal attack. Both PLATO-treated and dry heat-treated specimen were prepared and analysed, in order to study the influence of moisture during hydrothermal treatment of wood. The resistance against all of the s...
B F Tjeerdsma, M Stevens, H Militz
Thermal modification of non-durable wood species 2. Improved wood properties of thermal treated wood
1998 - IRG/WP 98-40124
Properties of wood treated in a new heat-treatment process called the PLATO-process have been studied. Several wood species have been treated using this new thermal modification process using a range of process conditions (mainly time and temperature). In this study the characteristics of the treated wood were determined using samples from whole planks treated on pilot plant scale. The modified ch...
B F Tjeerdsma, M J Boonstra, H Militz
Effects of heat treatment on modulus of elasticity of beech wood
2002 - IRG/WP 02-40222
Heat treatment is the oldest, simplest and cheapest method for reducing hygroscopicity of wood. The heat treatment protects wood against to biological organisms as well as giving
wood dimensional stabilization without damaging environment. The effects of heat treatment on modulus of elasticity (MOE) of beech wood (Fagus orientalis Lipsky) naturally grown and intensively used in forest products in...
S Yildiz, G Çolakoglu, Ü C Yildiz, E D Gezer, A Temiz
New applications of silafluofen to termite control
2001 - IRG/WP 01-30274
Silafluofen-based termiticides are widely used for soil and timber treatments in Japan, as silafluofen possesses advantageous properties of low fish toxicity and high chemical stability (to light, in soil, in alkaline environments, etc) in addition to high termiticidal activity and low mammalian toxicity. As new applications of silafluofen to termite control, we have developed another type of prod...
K Nakayama, Y Minamite, S Koike, Y Katsuda, K Nishimoto
Soft-rot in Tabebuia sp. wood used in water cooling tower:
identification and degradation capacity of the fungi
1998 - IRG/WP 98-10253
Tabebuia sp. (ipe), a native Brazilian wood, is considered of high natural resistance to decaying fungi, and has been used in harsh environments, as cooling towers. Fifty-one fungi, belonging to mitosporic fungi group (Fungi Imperfecti), were isolated from deteriorated Tabebuia sp. wood samples, collected from the mist eliminator and packing of a cooling tower in operation for about 23 years. The ...
S Brazolin, M Tomazello, I H Schoenlein-Crusius
Basidiospore structure and germination of Serpula lacrymans and Coniophora puteana
1988 - IRG/WP 1340
Using a nuclear staining technique and fluorescence microscopy, the basidiospores of Serpula lacrymans were shown to be uninucleate whereas those of Coniophora puteana were binucleate. The germination rate of the Serpula lacrymans spores, which was considerably lower than that of Coniophora puteana, decreased further after storage or heat treatment. Transmission electron micrographs indicate that ...
B M Hegarty, U Schmitt
Heat inactivation of mould fungi on wood
1993 - IRG/WP 93-40012
Heat treatments have been successfully used for eradication of dry rot. The effect of heat treatments at 40, 50 and 60°C for various time intervals on the inactivation of Penicillium brevicompactum was determined. The effect of heat on ungerminated spores and spores "pregerminated" for 24 hours was evaluated by plating on malt-extract agar. Although most ungerminated spores were inactivated after...
J Bjurman
New experiences with Dry Rot in Danish buildings, heat treatment and viability tests
1989 - IRG/WP 1423
An increasing number of concealed dry rot attacks, especially in older multi-storey houses under renovation, have been detected during the last few years. A necessary consequence is a demand for cheaper methods of repair, compared to the standard method used in Denmark for many years otherwise severely attacked houses will by pulled down. A heat-treatment has been developed and tested in practice....
A P Koch, C Kjerulf-Jensen, B Madsen
Biological resistance of steam-compressed wood pretreated with boric compounds
1999 - IRG/WP 99-30190
Wood compression under heating is aimed to enhance dimensional stability and surface hardness. Preservative treatment with an appropriate chemical is additionally required for the protection of wood against biological agents under hazardous service conditions. Boron pretreatment of compressed wood was targeted to a mutual benefit of increasing biological resistance of compressed wood as boron was ...
M K Yalinkilic, W Dwianto, Y Imamura, K Tsunoda, M Takahashi
The effect of added nutrients on growth rate and decay capacity of Serpula lacrymans
1990 - IRG/WP 1427
At the previous meeting a new technique was presented that enables both fungal growth rate and wood decay rate to be measured using the same timber specimen. The technique (IRG/WP/1384) has previously been carried out with 1% malt as the sole nutrient within the small jar that provides the inoculum for this method. Results presented here relate to an additional level of 5% malt, with or without a ...
J D Thornton, A McConalogue
Comparison of thermally modified wood originating from four industrial scale processes – durability
2002 - IRG/WP 02-40229
This study examined the differences in biological wood properties of heat treated wood originating from four different European industrial heat treatment plants. The manufacturers of heat treated material were: PLATO Hout B.V./Netherlands, Thermo Wood/Finland, New Option Wood/France and Menz Holz/Germany where Oil-Heat treated Wood (OHT) is produced.
The results of miniblock tests with basidiomyc...
C R Welzbacher, A O Rapp
The effect of heat treatment on the properties of spruce
1994 - IRG/WP 94-40032
The effect of high temperature treatment (above 150°C) on the wood quality is studied at the VTT. Improved dimensional stability, lower equilibrium moisture content and increased durability against biodeterioration is achieved, depending on the environmental factors. The biodeterioration resistance of spruce is improved due to changes in chemical composition and lower equilibrium moisture content...
H Viitanen, S Jämsä, L Paajanen, A J Nurmi, P Viitaniemi
Dimensational stabilisation of wood
1981 - IRG/WP 3171
A review is given of the studies on the dimensional stabilisation of wood which have been carried out in the laboratory 5.14 "Wood Technology" since 1967. All stabilisation methods known have first been compiled from the available literature. Practical studies were then started. Wood was treated with monomers (styrene, methyl metacrylate, isocyanate), formaldehyde, tannin and sugar. Despite a sati...
A Burmester
Information from the COIPM Wood Group
1988 - IRG/WP 4146
Abstract from the COIPM minutes: Wood in marine environment:
Mrs Gambetta stated that the main item discussed by the Group was the collaborative work to test the durability of heat shrinkable polyolephin sheating materials for the protection of wood against marine organisms. The work began last year when wood samples were sent out to the participants. Three samples of Pinus sylvestris wrapped in ...
A Gambetta
A comparative analysis of Coniophora olivacea (Fr. ex Pers.) Karst. and Coniophora puteana (Schum. ex Fr.) Karst. test strains
1993 - IRG/WP 93-20004
Investigations were carried out to compare pure cultures of Coniophora olivacea (Fr. ex Pers.) Karst. used as a test fungus in Australia and other Pacific countries, and Coniophora puteana (Shum. ex Fr.) Karst. which is used in Europe. Comparisons included morphology, growth rate and dry mass of mycelium, decay capacity, influence of temperature, toxic value of CCA and quaternary ammonium compound...
J Wazny, L J Cookson
Effects of steaming heat treatment of wood on the stimulation of termite feeding
1997 - IRG/WP 97-10212
At the 26th IRG conference, we reported that steamed Japanese larch heartwood samples were suffered a serious attack by subterranean termite, Coptotermes formosanus both in choice and no-choice feeding tests. This is possibly caused by the yield of termites stimulants in the wood samples resulting from the steaming process. Since the steaming heat treatment has often been applied to other several ...
S Doi, Y Kurimoto, M Takahashi, T Yoshimura
A comparison of fungal strains used in the bioassay of wood preservatives
1984 - IRG/WP 2220
Previously published data are presented relating to a number of strains of wood-destroying basidiomycetes (Coniophora puteana, Coriolus versicolor, Gloeophyllum abietinum, Gloeophyllum sepiarium, Gloeophyllum trabeum, Lentinus lepideus, Poria placenta, Fibroporia vaillantii and Serpula lacrymans) commonly used as test fungi in the bioassay of wood preservatives. The data, which has not been statis...
J Wazny, H Greaves
Bending strength of heat-treated spruce and pine timber
2002 - IRG/WP 02-40242
Heat-treatment of spruce (Picea abies) and pine (Pinus sylvestris) beams (45 x 145 mm) gave a reduction in bending strength of approximately 50%. The bending stiffness (modulus of elasticity) only decreased by 3.5%. Tests were carried out according to EN 408. Another effect of the heat-treatment was increased variation in bending strength. The 5th percentile value of the bending strength, the so c...
C Bengtsson, J Jermer, F Brem
Treatment groups and remedies for CCA treated hardwood and softwood poles
1999 - IRG/WP 99-40142
Different hardwood and softwood species from Bangladesh and Bhutan was investigated regarding density, green fiber stress, natural durability of heartwood and CCA treated sapwood, CCA treatability grades, sapwood thickness, and kiln-drying properties for long term use as electric poles. These properties along with the past service records for nineteen years, separated ten heardwood and five softwo...
A K Lahiry
Characteristics of thermally modified wood in vacuum
2004 - IRG/WP 04-40287
In commercial thermal wood modification processes nitrogen, steam or oil has been used for the reduction of oxygen content in the reactor atmosphere. In present study no special heating medium, but an initial vacuuming step has been used for this purpose. Mass loss, resistance to fungal decay, dimensional stability, bending strength and modulus of elasticity of heat treated wood were evaluated and...
G Rep, F Pohleven, B Bucar