Your search resulted in 88 documents. Displaying 25 entries per page.
Preliminary desk research in the Netherlands on development of a Knowledge Based System for Life Cycle Assessment of wood products
1997 - IRG/WP 97-50093
TNO is currently coordinating an EC-project (LIFE-SYS WOOD) to develop a consistent approach to Life Cycle Assessment (LCA) of wood products. Existing and new LCA-inventory data of six wood products will be evaluated on reliability and consistency. After validation, LCA-results will be made available through a Knowledge Based System (by 1998-1999). The aim of the KBS is to make LCA-results availab...
P Esser, D Robson, R Vanhauten
Development of a commercial-scale CCA chemical sludge recycling system
1993 - IRG/WP 93-50001-19
The occurrence of fixation reactions in Copper Chromium Arsenate (CCA) treatment solutions is increased where the treatment of unseasoned and partially seasoned timbers in hot climates occurs. The by-products of the fixation reactions are predominantly insoluble chromium arsenate compounds, commonly referred to as CCA sludge. Historically, this material has been disposed of into toxic waste landfi...
A J B Butler
Potential use of an emulsified tar oil fraction as a wood preservative: Preliminary technological and environmental assessment
1994 - IRG/WP 94-50028
In order to meet the recent environmental concern specifications of creosote are altered, the B[a]P content is limited and restrictions on the emission of volatile organic compounds (VOC) and higher polyaromatic hydrocarbons (PAH) are expected in some countries. Research has been conducted on an emulsion of a selected tar oil fraction. Using a waterborne formulation opens new perspectives for targ...
G M F Van Eetvelde, R Leegwater, M Stevens
PXTS; A Metal Free Oligomer Wood Preserving System - A Summary of Data To Date
2004 - IRG/WP 04-30350
The world is continually looking for new wood preservative technology, especially to address environmental concerns. Recent changes in the USA have limited the use of arsenical containing formulations to industrial use through a negotiated voluntary cancellation of most residential label uses. PXTS (Polymeric Alkylphenol Polysulfide) offers a brand new technology that is an all organic system, lik...
M H Freeman, D D Nicholas, D Renz, R Buff
Partial seasoning and preservative treatment systems for pine roundwood
1982 - IRG/WP 3187
Experimental trials at FRI, Rotorua showed that the steaming schedule normally used for steaming and venting is also suitable for steaming and vacuum seasoning. Applying vacuum of up to -84 kPa immediately after steaming did not increase the initial loss of wood moisture significantly in comparison to steam/venting. The main improvement to wood condition by using steam/vacuum appeared to be to dis...
A J Bergervoet
Biological variability in the oxalate/oxalate decarboxylase system among five isolates of the wood-degrading fungus Meruliporia incrassate
2006 - IRG/WP 06-10573
The “dry-rot” wood decay fungus Meruliporia incrassata has recently attracted attention, primarily in the western coastal United States, as a particularly destructive pest of building material. Recently, the US Environmental Protection Agency (EPA) has accepted a voluntary withdrawal of the historically effective chromated-copper arsenate (CCA) as a preservative for wood used in residential se...
C Howell, J Jellison
Water analysis in chemicals, wood or chemically treated wood using a new analytical method for selective water detection
2006 - IRG/WP 03-30391
Water or moisture content analysis can be a challenging task in many applications. However, knowing accurately the type of water which can be found in a given sample or product can provide important information about a chemical compound used for wood treatment and especially about the treated wood sample.
Moisture content in wood plays an important role in fungal growth and it needs to be extensi...
R Craciun, D Taylor
Surface and system treatments of wood for outdoor use
2006 - IRG/WP 06-30412
The project “Surface and system treatment of wood for outdoor use” was initiated the summer 2001. The project evaluates environmentally friendly preservatives and water borne coating systems, to find the best protection for timber indented for outdoor use. The wood species selected as test material were pine and spruce. The different treatments were exposed in several outdoor accelerated tests...
B Jacobsen, F G Evans
Community-wide suppression of R. flavipes from Endeavor, Wisconsin – Search for the Holy Grail
2008 - IRG/WP 08-10674
In 2006, the Forest Products Laboratory, in collaboration with Alternative Pest Solutions Inc. and the UW-Madison Entomology department, developed a strategy for sustained suppression/elimination of R. flavipes from Endeavor, Wisconsin. Our commitment includes a minimum of five years of active treatment followed by at least one year of monitoring. The Whitmire Micro-Gen Advance baiting system (a.i...
F Green III, R A Arango, G R Esenther
Development of an International Use Classification System
2008 - IRG/WP 08-20380
Working Party 2.5 of the IRG was set up in 1995 in response to discussion around proposals for an International Wood Preservation Standard. Two years later, ISO Technical Committee 165 Timber Structures set up a subcommittee SC1 Wood Materials – Durability and Preservation to address this issue. It was agreed that neither the European Hazard Class system nor any other regional system could be ...
P I Morris
The effect of different foundation systems against fungal flora in the crawl space of a new wooden Japanese house
2009 - IRG/WP 09-10700
In order to establish novel preventive measures against damage of wooden houses by decay fungi with less-use or no-use of chemicals, we periodically monitored the fungal flora in the crawl space of a new wooden Japanese house build with recyclable and low-environmental load materials at the Research Institute for Sustainable Humanosphere, Kyoto University. We employed either a layer of concrete or...
A Toyoumi, S Horisawa, T Yoshimura, S Doi,Y Imamura
Continuous moisture measurement (CMM) to detect failure of moisture resistance
2009 - IRG/WP 09-20422
A wood coating system will fail to perform properly after a certain time of weathering. From that moment, the substrate is especially prone to fungal attack. Moisture plays a key role on weathering performance, wood protection efficacy and decay susceptibility of wood. Therefore, knowledge of the moisture dynamics of the applied wood protection is of significant importance in the prediction of the...
I De Windt, J Van den Bulcke, J Van Acker
Component leaching from CCA, ACQ and a micronized copper quat (MCQ) system as affected by leaching protocol
2009 - IRG/WP 09-50261
Leaching results for Cu, Cr and As (CCA) and Cu (ACQ and MCQ) from southern pine are compared for laboratory tests (AWPA E11, and draft OECD methods I and II) and natural weathering of horizontally and vertically oriented lumber samples over two seasons. This paper expands on results and comparison of results presented at the IRG regional meeting in Costa Rica in Dec 2008 (Cooper and Ung 2008) a...
P A Cooper, Y T Ung
Selection of an appropriate coating system for wooden boats to be used in fresh water
2009 - IRG/WP 09-40472
Properties of several, most commonly used protective low-price coatings, which are used by the pletnja boat owners in Bled, Slovenia, were extensively studied. The aim of this professional, practically oriented study was to compare various coating systems, and to recommend the most suitable one to the boat owners. Regarding specific use conditions, the following properties, including their resista...
M Petrič, B Kričej, A Logar, M Pavlič
Observations on colony collapse in Reticulitermes flavipes (Kollar) in laboratory and field settings in Wisconsin
2010 - IRG/WP 10-10709
Parallel strategies were designed to eliminate Reticulitermes flavipes (Kollar) from a field site in Endeavor, Wisconsin and a simulated field test setup of approximately 20,000 workers in the laboratory. Indoor and outdoor colonies of R. flavipes were baited with commercial cellulose monitoring stations and rolled cardboard stations. If the commercial cellulose baits were attacked, they were repl...
F Green III, R A Arango, G R Esenther
The Relative Performance of an Organic Preservative System under UC3A and UC3B Conditions using Two Test Methods
2010 - IRG/WP 10-20429
Coated L-joints have been used for decades to evaluate the performance of wood preservatives in protected environments. This study was conducted using matched coated and uncoated L-joints to simulate above ground protected and unprotect exposures. When exposed to constant moisture in a greenhouse environment, coated and uncoated L-joints give very similar performance results. In contrast, exposi...
C F Schauwecker, A Zahora, A F Preston
Implementation of a Quality Assurance System for thermally modified timber (TMT) by the Association of Central European TMT-Producers
2011 - IRG/WP 11-40558
Due to increasing market shares of thermally modified timber (TMT) in Europe, a working group of ten central European TMT manufacturers (TMT-WG) was founded in 2010 to cover public relations and marketing activities. Since the present level of product testing and property declaration was not satisfying, a “task group TMT-quality” was put into action in 2010 to develop a comprehensive quality a...
C R Welzbacher, W Scheiding
The overview of ISPM 15 implementation in Croatian wood-working companies
2011 - IRG/WP 11-30576
Croatia is a small European county, but in the same time a great country according to it’s tradition in the forestry and wood working industry. However, around 48% of it’s territory is afforested. As the export is one of the main directions in the Croatian development conception, the production and distribution of wood package intended for the international trade, is one of the most important ...
R Despot, V Jambrekovic, M Hasan
Use of the durable species Coast Redwood as a reference system for field testing of Wood Protection systems
2012 - IRG/WP 12-20486
Data is provided and discussed for a number of field exposure tests where the naturally durable wood species Coast redwood, Sequoia sempervirens, was included along with untreated pine and standard preservative treatments. In general, there is potential for higher variability of results with this naturally durable species, but it does suggest that redwood can be a useful reference material for te...
A Zahora, A Preston, L Jin
Smart hydrogels from low molecular weight amphiphilic compounds: toward a solution to decrease leachability and increase efficacy of boron preservatives?
2012 - IRG/WP 12-30589
A new catanionic system associating amphiphilic carnosine (AlaHisC8) and lauric acid forms supramolecular hydrogel at very low concentration. This gel was investigated and we have checked the validity of the concept of hydrogels utilization to reduce boron leachability and to develop new wood protection treatments. Impregnation with 5% aqueous borax solution (w/w) and 0.3% gelator agent (...
F Obounou Akong, P Gérardin, C Gérardin-Charbonnier
System treatments of Pinus sylvestris - influence on moisture, decay and discoloration
2013 - IRG/WP 13-30612
Biological activity can cause challenges for the use of wood in outdoor exposure. Decay and discolouring fungi influence the service life of wooden constructions, and the moisture content of the wood is often an important factor. The aim of this study was to evaluate the performance of different combinations of preservative/modified wood protection treatments and surface treatments for wooden deck...
A Schabacker, G Alfredsen, L Ross Gobakken, H Militz, P O Flæte
The Chelator Mediated Fenton System in the Brown Rot Fungi: Details of the Mechanism, and Reasons Why it has Been Ineffective as a Biomimetic Treatment in some Biomass Applications – a Review
2014 - IRG/WP 14-10828
The chelator-mediated Fenton (CMF) reaction requires the action of two types of chelating compounds. The first chelator, oxalate, solubilizes and then sequesters iron, and the second chelator reduces iron. Iron reduction must be controlled near the fungal hyphae to prevent damaging Fenton chemistry from occurring in that location. Similarly, iron reduction must be promoted within the wood/plant ce...
B S Goodell, M Nakamura, J Jellison
Experiences with an industrial system for controlled thermal wood modification in pressurized unsaturated steam
2014 - IRG/WP 14-40678
Thermal wood modification in pressurized reactors has a long history, but these processes are to date industrially scarcely used, because of the relatively complicated process equipment, compared to the more common high-temperature processes in kilns at atmospheric pressure. However, based on our practical experience with the FirmoLin® process, supported by recent scientific findings, it is foun...
W Willems
Termite Management and the U.S. Experience: A Case for Wood Treatment & Integrated Control
2015 - IRG/WP 15-30678
A brief overview of termite control is given using specific experiences from the U.S.A. Five major types of termite treatment now prevail: soil applied chemical barriers, in-structure chemical barriers (in-situ applied wood and foundation treatments), physical barriers, treated wood and termite baits. In general, ‘stand-alone’ pretreatments or ‘primary’ treatments are often discussed and ...
J D Lloyd, K van den Meiracker
Above-ground performance of a buffered amine oxide treatment system against Mastotermes darwiniensis
2016 - IRG/WP 16-10855
Above-ground H2 field tests against Mastotermes darwiniensis were conducted in far north Queensland to assess the efficacy of buffered amine oxide treatments in the softwoods Pinus sylvestris and P. radiata, and the hardwoods Eucalyptus regnans and E. diversicolor. Untreated hardwoods and slash pine bait wood (P. elliottii) were severely attacked or destroyed, while untreated P. sylvestris was mod...
L J Cookson, R W Clawson Jr