Your search resulted in 789 documents. Displaying 25 entries per page.
Variations of Furfuryl alcohol and Wolmanit CX-8 treatability of pine sapwood within and between trees
2008 - IRG/WP 08-40421
The variations on the ratio of filling (RoF) were investigated on Norwegian grown Scots pine (Pinus sylvestris). The samples were taken from 10 different stands in south-east Norway, and treated with furfuryl alcohol and a copper-containing wood preservative. Both within tree variations, between tree variations and variations between stands were investigated for significant differences. Factors li...
E Larnøy, S Lande, G I Vestøl
Cantilever bending test of furfurylated poles
2008 - IRG/WP 08-40424
Ten, 8 m long poles of Scots pine (Pinus sylvestris) were treated with furfuryl alcohol to a WPG of approximately 40 %. A bending test was performed according to the principles in the draft European standard for wooden poles, prEN 14229 - Structural timber - Wood Poles for overhead lines. The bending strength and stiffness (MOE) for the poles tested were compared to an earlier study by the Swedish Wood Preservation Committee. In the latter study untreated, CCA-treated, ammoniacal Cu-PCP treated and creosoted poles were tested in bending. These types of poles were considered not to differ in strength and stiffness. The results of the furfurylated poles fit well with the results from the previous study. The bending strength and MOE values obtained are compared to the upper and lower 95-percentile values of the results from the previous study and all poles treated with furfuryl alcohol fit within this interval.Thus, this study indicates that a treatment with furfuryl alcohol does not result in a decrease of strength or stiffness. Further testing with a larger population of poles is necessary in order to get a statistically reliable result. In addition to further demonstration of the durability, the
treatment process must be optimised to ensure full sapwood penetration and measures have to be taken to avoid the serious cracking observed in this trial before furfurylation can be considered for treatment of Pinus sylvestris poles.
R Ziethén, J Jermer, A Clang
To decay or not to decay: An accelerated field test of the validity of the Scheffer index
2008 - IRG/WP 08-20392
The Scheffer Index was introduced in 1971 to predict the relative decay hazard of untreated wood exposed above-ground. Precipitation and temperature parameters are used in the calculation. A higher Scheffer Index value implies a greater risk of decay. An accelerated 18-month study using seven field sites with Scheffer Indices ranging from 35 to 400 and two wood types (Populus tremuloides and Pi...
G M Larkin, P E Laks
Estudio comparativo entre postes de Eucalyptus saligna Smith, Pinus caribaea Morelet (pino macho) y Hormigón
2008 - IRG/WP 08-40436
As consequence of the Energy Revolution and the amplification of the communication networks, Cuba carries out significant expenditures of foreign currencies in the import of public service posts. It is presented in this work a synthesis of the current problem in Cuba of the public service posts (PSP), since as answer to the stocks of improvement of the national Electric System, the demand of this ...
C Sosa Suárez, I D Velázquez Viera, K Manzanares Ayala
Termite resistance of pure and mixed heartwood-sapwood Cypress (Cupressus sempervirens L.) plywoods
2009 - IRG/WP 09-10693
The main objective of this research was to evaluate the ability of different plywoods made of durable heartwood and/or non-durable sapwood to resist termite damage. The well-known durable cypress (Cupressus sempervirens) was chosen for this study. The natural durability of cypress solid wood, divided into sapwood and heartwood, as well as the durability of 17 different laboratory manufactured plyw...
F Faraji, M-F Thévenon, B Thibaut
Preservación de madera en Uruguay
2008 - IRG/WP 08-30492
Uruguay has a temperate climate and predominantly gently undulating landscape which is naturally suitable for farming activities. Therefore, its economy has always been based upon them and the related industries. In the sixties, the government decided it was necessary to increase forested areas in the country. Based on different consultancies, the legal frame was built in order to promote a sustai...
S Böthig
Gene expression of selected decay enzymes produced during biodeterioration of three wood types
2009 - IRG/WP 09-10702
Comparative studies were conducted on the expression of several decay enzyme genes during the decay of pine, cedar, and ACQ treated pine over 10 months. Measurements of MOE, decay rating, and moisture control were monitored for physical properties. Identification of decay fungi and the detection of decay enzymes were carried out before gene expression levels were measured. The MOE of wood stakes d...
Young-Min Kang, L Prewitt, S Diehl
European House Borer Hylotrupes bajulus Linnaeus in Western Australia: the anatomy of an eradication program
2009 - IRG/WP 09-20403
In January 2004, European house borer (EHB) Hylotrupes bajulus Linnaeus was detected in Perth, Western Australia. A containment program was set up and expanded to a full eradication campaign in 2008. The program is projected to eradicate EHB by 2021. This paper describes research work and assumptions on the biology and behaviour of EHB in Western Australia, surveillance and control methods, commun...
M Grimm, R J Cunningham, M Castalanelli, D Collins, L Vagg
Colour change monitoring of photodegradation in Scots pine (Pinus sylvestris) – a short term focus
2009 - IRG/WP 09-40442
Colour change monitoring of photodegradation is a quick and easy method for monitoring rates of photodegradation in timber. A study was undertaken to compare this technique to other monitoring methods, including microtensile strength changes and weight loss. Colour changes due to accelerated sunlight exposure were monitored using a Datacolor check spectrophotometer and compared with a set of contr...
V Sharratt, C A S Hill, D P R Kint
Effectiveness of a superficial treatment of bifenthrin to protect softwood framing from damage by subterranean and drywood termites in Indonesia
2009 - IRG/WP 09-40443
Various experimental testing procedures were undertaken in Indonesia to determine the effectiveness of a superficial (envelope) treatment of bifenthrin to protect softwood framing from damage by two species of subterranean termite (Macrotermes gilvus and Coptotermes curvignathus) and one species of drywood termite (Cryptotermes cynocephalus). Lengths of framing (Pinus radiata sapwood) were commerc...
P Sukartana, J W Creffield, A Ismanto, N E Lelana
Microwave Surface Modification of Radiata Pine Peeler Cores for Preservative Treatment
2009 - IRG/WP 09-40453
Radiata pine peeler cores are classified as a by-product derived from the cores of logs left over after the veneer peeling process. The core can be potentially developed for value added solid wood products as it is abundantly available and has a constant diameter. However, the core needs to be preservative treated because of low durability in ground contact. An additional problem is that the wood ...
K Sugiyanto, G Torgovnikov, P Vinden
Microscopy evaluation of microbial decay patterns in wood stakes after 6 years in soil contact
2010 - IRG/WP 10-10715
Most studies on wood modification have so far been concerned with service life predictions rather than investigating the decay protection mechanism. Very little is known about the mode of action of these new treatments and about the strategies used by wood degraders in order to utilize the wood material despite a treatment. Access to such knowledge would allow further modification and improvement ...
A Pilgård, C G Björdal
Adsorption of ionic liquids by Scots pine wood (Pinus sylvestris L.) and beech (Fagus sylvatica L.): equilibrium and kinetic modeling
2010 - IRG/WP 10-20447
In this paper methods for the adsorption study of quaternary ammonium-based ionic liquids on Scots pine (Pinus sylvestris L.) and beech (Fagus sylvatica L) are presented. Kinetic and equilibrium adsorption of compounds were evaluated. The equilibrium data fitted very well to the Langmuir adsorption models. The highest correlation coefficients determined from the pseudo-second order kinetic model ...
J Zabielska-Matejuk, A Stangierska, M Kot
Assessment of Boracol 200RH (FrameSaver) as a remedial treatment to control decay in pre-decayed model timber frame units
2010 - IRG/WP 10-30529
Model timber frame units constructed from untreated radiata pine were pre-wetted to approximately 40% moisture content and inoculated with Coniophora puteana and Oligoporus placenta. Units were transferred to a controlled environment room maintained at 25°C and 95% RH for 7 and 10 weeks to allow two levels of decay to become established in units. Following pre-decay, units were disassembled, clea...
Mick Hedley, Dave Page, Jackie van der Waals
Chemical protection of historic timber structures: Results and future needs
2010 - IRG/WP 10-40487
The paper concentrates on the analysis of the effectiveness of chemical protection for timber structures in the Russian State Museums “Kizhi” (Karelia) and “Vitoslavlitsy” (Novgorod).
The condition of historic timber was tested at the monuments treated with PCP, borax, potassium carbonate, boric acid, Pinotex chemicals in the 1970-80. Long-term analysis revealed that in many cases the...
M Kisternaya, V Kozlov
Fungal decay resistance and mechanical properties of plywood panels made from maritime pine (Pinus pinaster) and bonded with cornstarch-quebracho tannin-phenol formaldehyde adhesive
2010 - IRG/WP 10-40490
The aim of this work is to demonstrate the performances of cornstarch-quebracho tannin-based resins designed as adhesive in the plywood production. In this way, the cornstarch and quebracho tannin was introduced in the classic adhesive formulation in order to supply a part of phenol-formaldehyde (PF). In order to evaluate the mechanical performances of optimal cornstarch-quebracho tannin-PF, plywo...
F Charrier, A Moubarik, A Allal, A Pizzi, B Charrier
Testing of decay resistance of sapwood and heartwood of thermally modified Scots pine and Norway spruce
2010 - IRG/WP 10-40523
Thermal modification at elevated temperatures changes the chemical, biological and physical properties of wood. One of the main targets of thermal modification is to increase the biological durability and decay resistance of wood. Although the effects of thermal modification on wood have been widely studied, the significance of sapwood and heartwood on the resistance of thermally modified wood has...
H Viitanen, S Metsä-Kortelainen
Basidiomycete colonization of Scots pine sapwood quantified by qPCR and TGA
2011 - IRG/WP 11-10750
Scots pine (Pinus sylvestris L.) is an important softwood species in Northern Europe and is frequently used as material for various wood protection systems. In Europe, EN 113 is the standard basidiomycete laboratory durability test method, using mass loss as evaluation criteria. In this paper quantitative real-time PCR (qPCR) and thermogravimetric analysis (TGA) was used to characterize coloniza...
G Alfredsen, S Bollmus, T K Bader, K Hofstetter
LOSP for glulam, when should the treatment be applied?
2011 - IRG/WP 11-30555
Treatment options for outdoor above-ground (H3) exposed glulam of Pinus radiata and P. elliottii were examined. Beams were treated with azole LOSP (containing a zinc tracer) aiming for retentions of 35-40 l/m3 or 70-80 l/m3. Treatment was conducted either before or after gluing. TBTN LOSP and CCA were included as comparative treatments. Test specimens for exposure were cut after treatment, while w...
L J Cookson
Comparison of rates of wood decay from four different field test protocols following 4-5 years exposure at a site in New Zealand
2011 - IRG/WP 11-30565
The rate of decay of Pinus radiata was evaluated using four different field test protocols at a site near New Plymouth, New Zealand. The average Scheffer index was 86 over the five year period of testing. The field tests were an in-ground stake test (AWPA Std E7-01) and three above ground tests – lap-joint (AWPA Std E16-98), decking (AWPC protocol) and ground proximity tests (AWPA Std E18-06) T...
P Lobb, K Day, A Siraa
The potential of silicone-based formulations to enhance wood properties through industrial treatment for outdoor use
2011 - IRG/WP 11-30578
High hygroscopicity is one of the main weaknesses of wood as far as its susceptibility to biodegradation, and specifically to fungal decay. New wood preservation technologies are constantly entering the wood protection market, competing with traditional, biocide-based preservation. Silicones are commercially used as hydrophobic agents on stones and concrete. They belong to the restricted number of...
F Simon, F Marchal, F Pochon, M Kutnik, I Le Bayon
Biological and mechanical performances of particleboard panels made from maritime pine (Pinus pinaster) and glued with cornstarch-mimosa tannin-urea formaldehyde adhesive
2011 - IRG/WP 11-40542
The objective of this work was to demonstrate the utility of cornstarch-mimosa tannin-based resins designed for application as an adhesive in the particleboard production. Bond qualities of cornstarch-mimosa tannin- urea formaldehyde (UF) (10:4:86, weight ratios) resins and commercial UF resin were assessed by using an automatic bonding evaluation system, prior to production of particleboard panel...
A Moubarik, F Charrier, A Pizzi, A Allal, B Charrier
Acetylation Properties of Southern Pine and Radiata Pine
2011 - IRG/WP 11-40543
The chemical modification of wood via acetylation with acetic anhydride has been a well investigated technology and is of current commercial interest due to improved properties such as dimensional stability as well as resistance to termites and resistance to rot and decay fungi. Despite this, the acetylation of a board substrate requires further investigation in order to assess board properties a...
J Allen, T Guinn, J Dickerson
Decrease of stiffness properties of degraded wood predicted by means of micromechanical modeling
2011 - IRG/WP 11-40570
Wood exhibits a highly anisotropic mechanical behavior due to its heterogeneous microscopic structure and composition. Its microstructure is organized in a strictly hierarchical manner from a length scale of some nanometers, where the elementary constituents cellulose, hemicelluloses, lignin, and extractives are found, up to a length scale of some millimeters, where growth rings composed of earlyw...
T K Bader, K Hofstetter, G Alfredsen, S Bollmus
Preference of Reticulitermes flavipes (Kollar) for Southern Pine Blue-Stained Sapwood from Beetle-Killed Trees
2012 - IRG/WP 12-10763
Bark beetles and their associated Ophiostomatiod fungi are the major pests of pine forests in the southeastern USA, and termites are the major insect decomposers of dead trees and wood products in the southeastern USA. While both are the principal destructive insects of southern pine trees and southern pine lumber, respectively, no relationship between the two has apparently been reported in the ...
N S Little, J J Riggins, A J Londo, T P Schultz, D D Nicholas